background image

 

  

 

AirFinder Quick Start Guide

 

11 

 

5.

 

ETL Warnings (English and French) 

1. For connection to a supply not in the U.S.A., use an attachment plug adapter of the proper 
configuration for the power outlet, if needed.

 

Pour la connexion à une alimentation pas aux Etats-Unis, utilisez un adaptateur de fixation de la 
configuration correcte pour la prise d'alimentation, si nécessaire.

 

2. Caution: Risk of Electric Shock. Grounding continuty must be maintained.

 

Attention: RISQUE DE CHOC ÉLECTRIQUE. La continuité de la mise à la terre doit être maintenue.

 

3. For indoor use only.

 

POUR UNE UTILISATION EN INTÉRIEUR.

 

4. Please check prior use, if output voltage and current of the power supply is suitable for the product.

 

Se il vous plaît vérifier avant l'utilisation, si la tension de sortie et le courant de l'alimentation est adapté 
au produit.

 

5. For information technology equipment use only.

 

Pour l'utilisation des équipements de technologie d'information seulement.

 

6. The plug is used as disconnect device. The socket-outlet shall be installed near the equipment and 
shall be easily accessible.

 

La prise est utilisée comme dispositif de déconnexion. La prise de courant doit être installée près de 
l'équipement et doit être facilement accessible.

 

7. The cover may under no circumstances be opened. If the cover is damaged, then the power supply 
may no longer be used.

 

Le couvercle peut en aucun cas être ouvert. Si le couvercle est endommagé, l'alimentation ne peut plus 
être utilisé.

 

8. Children should be supervised to ensure that they do not play with the appliance.

 

Les enfants doivent être surveillés pour s'assurer qu'ils ne jouent pas avec l'appareil.

 

 

 

Summary of Contents for AirFinder 3.0















Reviews: