background image

1

1

st

Installation Instructions

For your safety and equipment, please be sure to read the safety instructions carefully

before using this equipment.

If you are in doubt, please read the manual. It has a detailed description of the device

operation. If you still have any questions, please contact us and we will give you a
satisfactory reply as soon as possible.

There is no extra-notice if the specification is changed.

Equipment installation, please note the following:

1.1. Power supply:

This device uses 12V/3A

power adapter, power adapter support 100-240V AC voltage input,

in order to make the device can work normally, please do not use other power adapter.
1.2. Power off:

When you need to move the equipment or other work that needs to be cut off power, turn

off all the power and unplug the power plug to ensure the safety of the equipment.
1.3. Cable:

Can not be in power lines, signal lines, communication lines and other cables on the items,

should avoid the cable was trampled or squeezed to prevent leakage or short circuit and other
dangerous.
1.4. Signal line connection:

When the device is inserted and pulled out, the equipment needs to be power off to avoid

damage to the equipment. Damage caused by live plug is not within the scope of warranty.
1.5. Cooling hole:

The outer surface of the equipment may have a hole for heat dissipation, do not plug the

openings, so as not to heat accumulation, damage to equipment or cause fire hazards.
1.6. Equipment placement:

Reasonable placement of equipment, such as the standard frame, chassis, cabinets, or

placed in a stable and smooth work table, to prevent the equipment fall.
1.7. The environment:

Equipment working environment should pay attention to dust, moisture, especially to

prevent liquid immersion and splashing into the equipment.
1.8. Maintenance:

All maintenance work should be done by professional maintenance personnel. In order to

prevent the risk of electric shock, do not open the cabinet.

Summary of Contents for LM-AD01










Reviews: