background image

Lens

Guide

Lens

Tab

Lens

Slot

75 Watt (Max)

Light Bulb

The Chamberlain Group, Inc.
STEP 7 Install Lights and Lenses
10/7/91 - 5/2/92

Lens Slot

75 Watt Max.

Light Bulb

Lens Tab

Light
Lens

 Screw

Panel

Install the light(s)

• Install a 75 watt maximum light bulb in each

socket. The light(s) will turn ON and remain lit for
approximately 4-1/2 minutes when power is
connected. Then the light(s) will turn OFF.

• If the bulbs burn out prematurely due to vibration,

replace with a "Garage Door Opener" bulb.

Install the lenses:  (Model 1260) Figure 1

• Slide lenses into guides. Snap bottom tabs into

lens slots.

• Reverse the procedure to remove the lenses.

Install the lens:  (Model 1245) Figure 2

• Locate and loosen (approximately 1/8") the two

screws near top of opener front panel. Position
lens against panel with slotted tabs directly below
screws. Slide lens up to seat tabs behind screws.
Snap bottom tabs of lens into panel slots.
Retighten top panel screws to secure lens.

Installation Step 7

Install the Light(s) and the Lens(es)

Installation Step 8

Attach the Manual Release
Rope and Handle

Do not use the red handle to pull the door
open or closed.

The rope knot could become

untied and you could fall. Use the manual
release only to disengage the trolley and, if
possible, only when the door is closed.

Garage doors are heavy. If the door is open
when the handle is pulled, the door could
close inadvertently if it is not properly
balanced. Serious injury may result to persons
under the door. Make sure the doorway is clear
of persons and obstructions before pulling
handle when door is open.

• Thread one end of the rope through the hole in the

top of the red handle so "NOTICE" reads right side
up as shown. Secure with an overhand knot.

The knot should be at least 1" from the end of the
rope to prevent slipping.

• Thread the other end of the rope through the hole in

the release arm of the outer trolley.

• Adjust rope length so the handle is 6 feet above the

floor. Secure with an overhand knot.

If it is necessary to cut the rope, heat seal the cut
end with a match or lighter to prevent unraveling.

Manual Release Rope and Handle

10/7/91

Trolley

NOTICE

Overhand

Knot

Manual

Release Handle

Rope

Overhand

Knot

Trolley

Release Arm

15

WARNING

CAUTION

WARNING

Lens

Guide

Lens

Tab

Lens

Slot

75 Watt (Max)

Light Bulb

The Chamberlain Group, Inc.
STEP 7 Install Lights and Lenses
10/7/91 - 5/2/92

Lens Slot

75 Watt Max.

Light Bulb

Lens Tab

Light
Lens

 Screw

Panel

Figure 1

Figure 2

Summary of Contents for 1245 - 1/3HP





































Reviews: