Linkcom Link Gate GSM ISDN User Manual Download

Page: 20 / 22

Ce document est la propriété de Linkcom.

Toute reproduction même partielle est strictement interdite

classe

classement

LGISDNeng 6.5

numéro

002.02

date

09/11/04

page

20/22

For starting the mail server click on ‘start’:

Setup a mail client

Here are the settings of SMS MA IL:

POP

: IP or name of the computer w hich is connected to the Linkgate

SMTP

: IP or name of the computer w hich is connected to the Linkgate

Please make sure you are using the good communication ports.

Send and receive SMS :

If you w ant to correctly distribute the received SMS, you must respect the follow ing rules:
-the SMS should contain the name of the computer

OR
-the alias of the computer name

In a received message the sender should w rite the name of the computer as follow :
#name_of_the_computer_or_alias# body of the SMS
You can send a SMS to multiple computers by separating the names w ith a coma:

#name01,name02,name03…# body of the SMS

If you w ant to send a SMS from your pop client, please use the follow ing syntax:

SM S@XXXXXXXXXXX.sms

, the X’s represents the phone number of the receiver

After a mail synchronisation the SMS MA IL server w ill extract the phone from the address

SM S@XXXXXXXXXXX.sms

and w ill send it through the GSM netw ork.

Summary of Contents for Link Gate GSM ISDN























Search results

Summary of Contents for Link Gate GSM ISDN

Reviews:

Related manuals for Link Gate GSM ISDN

Brands by name

Popular brands

Linkcom Link Gate GSM ISDN, User Manual

Search results

Summary of Contents for Link Gate GSM ISDN

Reviews:

Related manuals for Link Gate GSM ISDN

Brands by name

Popular brands