background image

4

Operating your CW-80 Transformer safely

Y

our Lionel CW-80 Transformer is listed by Underwriter’s Laboratory Inc. and has been 
carefully designed to ensure peak performance. When using electrical products, basic 

safety precautions should be maintained. 

Be sure to observe the following guidelines:
•  Read the manual thoroughly before using this device.
•  This device is not recommended for children under fourteen years of age.
•  Parents should periodically inspect this product for potential hazards and, if necessary, 

have them repaired by an authorized Lionel Service Center. In the event that such a condi-
tion exists, the transformer should not be used until it has been properly repaired.

•  The CW-80 Transformer is intended to be used indoors. Do not use this device if water is 

present. Serious or fatal injuries may result.

•  Use the CW-80 Transformer only for its intended purpose.
•  The CW-80 Transformer was meant to operate on 120-volt, 60-Hertz power. Do not connect 

this product to any other power supply.

•  Do not operate the CW-80 Transformer with a damaged cord, plug, or case.
•  To avoid the risk of electrical shock, do not disassemble the unit. There are no user service-

able parts inside. If damaged, take this product to an authorized Lionel Service Center. Visit 
www.lionel.com for a list of authorized Service Centers.

•  Do not operate the CW-80 Transformer on your layout unattended. Obstructed accessories 

or stalled trains may overheat, resulting in damage to your layout.

•  Always unplug the CW-80 Transformer from the power source when not in use.
•  Never insert objects into the ventilation slots on this product. Damage to sensitive  

electronic components can result.

Creating your layout

Summary of Contents for NJ Transit

























Reviews: