background image

19

TrainMaster Command Control operations

CAB-1 Remote Controller commands

T

he CAB-1 Remote Controller commands are detailed below. The corresponding RailSounds 
sound system effects are in bold italic type.

Releases the ElectroCoupler on the rear of the 
tender.

 Coupler release sound.

Activates the numeric keypad. 

Short steam release sound.

Controls switch direction. Toggles all lights on/off, 
except lights that are wired to track power. 

Accelerates the locomotive with a clockwise 
rotation. Decelerates the locomotive with a 
counter-clockwise rotation. 

Speed-dependent   

chuffing sounds. DynaChuff dynamic chuffing 
effect. 

Activates the locomotive’s whistle. Release the 
button to discontinue the sound. 

Whistle sound 

with steam effect.

    

Toggles the bell sound on and off. 

Bell sound.

Changes the locomotive’s direction. The locomotive 
decelerates to a stop and continues in the opposite 
direction when you increase the throttle. 

Air 

release sound.

Increases the locomotive’s speed while the button is 
pressed. Release the button to return to the initial 
speed. 

Labored chuff.

Decreases the locomotive’s speed while the button is 
pressed. 

Squealing brake sounds.

Shuts down all PowerMasters on your railroad. Stops 
all TrainMaster Command Control-equipped 
locomotives in operation. Use HALT only in 
emergency situations.

SET

L

M

H

Odyssey II Momentum

L     

32 speed steps with low 

momentum

M

    100 speed steps with low 

momentum 

    100 speed steps with medium 

momentum

Summary of Contents for VISION Line 700E Hudson

































Reviews: