Lippert 191025 Installation And Owner'S Manual Download

Page: 1 / 16

lippert.com

432-LIPPERT (432-547-7378)

Rev:06.30.22

JT’s Strong Arm

™

Travel Trailer

Installation and Owner’s Manual

(For Aftermarket Applications)

CCD-002345

Table of Contents

Introduction

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Resources Required

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Preparation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation for Scissor Jacks

. . . . . . . . . . . . . . . . . . . . . . . . . .

Chassis Specific Instructions: “I” or “H” Beam

. . . . . . . . .

Operation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Scissor Jack Extend

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Scissor Jack Retract

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

JT’s Strong Arm

Travel Trailer

Installation and

Owner’s Manual

(For Aftermarket Applications)

JT’s Strong Arm Travel Trailer Aftermarket Kit

Part #

Part # Description

Description

191025

JT’s Strong Arm Travel Trailer Jack Stabilizer

Electric Stabilizer Jack Pad Adapter Kit

. . . . . . . . . . . .

Resources Required

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electric Stabilizer Jack Pad Aftermarket Adapter Kit

Installation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Notes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Summary of Contents for 191025

















Search results

Summary of Contents for 191025

Reviews:

Related manuals for 191025

Brands by name

Popular brands

Lippert 191025, Installation And Owner'S Manual

Search results

Summary of Contents for 191025

Reviews:

Related manuals for 191025

Brands by name

Popular brands