background image

11              

lippert.com 

    432-LIPPERT (432-547-7378)   

Rev: 06.15.22

SureShade

® 

Power 

Bimini Upgrades: Fly 

Extension

Installation and Owner’s Manual

(For Aftermarket Applications)

CCD-0004538

Troubleshooting

What is happening?

What is happening?

Why?

Why?

What should be done?

What should be done?

Fly extension stanchions do not 

reach the locking plates.

Fly extension not fully extended.

Fully extend fly extension.

Bimini top not fully extended.

Fully extend bimini top.

Locking plates mounted too far away.

Relocate locking plates.

Stanchions do not lock in-place.

Bad locking button.

Contact Lippert.

Email: customerservice@lci1.com 

Phone:  432-LIPPERT (432-547-7378)

Tie-down strap does not reach the 

saddle.

Saddle mounted too far away.

Relocate saddle.

Tie-down strap not extended enough.

Adjust tie-down strap buckle to increase 

strap length.

Tie-down strap clip does not close 

on saddle or stanchion.

Bad spring clip.

Replace tie-down strap.

Maintenance

Fabric Care

The fly extension can be cleaned while installed on the 

boat or separately when removed.

NOTE: 

It is good practice to clean the fly extension at the 

same time when cleaning the bimini top.
Use clear water to consistently hose off the fly extension 

fabric during the boating season.
When necessary, a deeper clean of the fly extension fabric 

can be done as follows:

1. 

If necessary, remove the protective boot, fully extend 

the bimini top and attach the fly extension to the front of 

the boat.

2. 

If the top and extension was stored wet, allow the boot, 

top and extension fabric to dry.

3. 

Remove any loose dirt and debris from all fabric.

4. 

Hose down the top, extension and boot fabric with 

clear water.

5. 

Prepare a mixture of 

1/4

 cup of mild dish soap and five 

gallons of warm water.

NOTE: 

Do 

NOT

 use harsh detergents.

6. 

Use a soft bristle brush to apply the soapy water to the 

fabric to remove stains and embedded dirt.

7. 

Allow the solution time to soak completely into the fabric. 

8. 

Hose off the top, extension and boot fabric with fresh, 

clear water. Repeat rinse if necessary.

9. 

Allow bimini top, fly extension and boot to dry before 

storing the extension, closing the top and installing the 

protective boot.
If cleaning the fly extension separately:

A. 

Unzip the extension fabric from the bimini top.

B. 

Slide the extension fabric to one side of the front tube 

so the two sections of the tube can be separated.

C. 

Completely remove the fabric from the tube.

DO NOT MACHINE WASH OR MACHINE DRY THE 

EXTENSION FABRIC OR DAMAGE TO THE FABRIC 

CAN RESULT. HAND WASH AND LINE DRY FABRIC 

ONLY.

D. 

Hand-wash the fabric by following the same, previous 

procedure for cleaning the open bimini top and extension.

NOTE: 

Do 

NOT

 machine wash or machine dry the 

extension fabric. Hand wash and line dry only.

Summary of Contents for SureShade Power Bimini 2021013744













Reviews: