background image

Warranty.

Parts Replacement.

For parts and information, please refer to
"Parts Inventory" on page 2.
Litex Customer Support:

1-800-527-1292

page 9

Troubleshooting.

Problem: 

Fan fails to operate.

Solutions:

1. Check wall switch to fan.
2. Verify that reverse switch is set completely in 
either direction.
3. Check to be sure fan is wired properly.

Problem: 

Light kit not lighting.

Solutions:

1. Check wall switch to fan.
2. Check that bulbs are installed correctly.
3. Check to be sure wires in canopy are wired 
properly.
4. Check to be sure that bulbs total no more than 
190W. 

[Note: Lamping light kit with bulbs that total more 

than 190W will cause the wattage limiting device to 
interrupt the flow of electricity to the light kit.]

Problem: 

Fan operates but lights fail.

Solutions: 

1. Check that bulbs are installed correctly.
2. Check to be sure wires in canopy are wired 
properly.
3. Verify that molex connections are connected 
properly in switch housing.
4. Replace defective bulbs with same type of 
bulb.
5. Check to be sure that bulbs total no more than 
190W. 

[Note: Lamping light kit with bulbs that total more 

than 190W will cause the wattage limiting device to 
interrupt the flow of electricity to the light kit.]

Problem: 

Fan wobbles.

Solutions:

1. Use the balancing kit in one of the hardware 
packs. 

If no blade balancing kit is provided, please 

call Customer Support, 1-800-527-1292, to request 
one.

2. Check to be sure set screw(s) on motor 
housing yoke is (are) tightened securely.
3. Check to be sure set screw on hanging ball is 
tightened securely.

LITEX LIFETIME LIMITED WARRANTY:
LITEX INDUSTRIES, LTD. warrants this fan to the original 
household purchaser for indoor use under the following 
provisions:
1-YEAR WARRANTY: LITEX INDUSTRIES, LTD. will replace or 
repair any fan which has faulty performance due to a 
defect in material or workmanship. Contact Litex Customer 
Service at 

1-800-527-1292

 to arrange for return of fan. 

Return fan, shipping prepaid, to Litex Industries, Ltd. We will 
repair or ship you a replacement fan, and we will pay the 
return shipping cost.
5-YEAR WARRANTY: LITEX INDUSTRIES, LTD. will repair or 
replace, at  no charge to the original purchaser, any fan 
motor that fails to operate satisfactorily when failure 
results from normal use.
RETURN FAN MOTOR ONLY, shipping prepaid, to Litex 
Industries. We will repair or ship purchaser a replacement 
motor and Litex will pay the return shipping cost.
6-YEAR to LIFETIME LIMITED WARRANTY: LITEX 
INDUSTRIES, LTD. will repair the fan, at no charge to the 
original purchaser for labor only, if the fan motor fails to 
operate satisfactorily when failure results from normal use. 
Parts used in the repair will be billed to the purchaser at 
prevailing prices at time of repair.
    The purchaser shall be responsible for all costs incurred 
in the removal, reinstallation and shipping of the product 
for repairs.
    This warranty does not apply when damage from 
mechanical, physical, electrical or water abuse results in 
causing the malfunction. Deterioration of finishes or other 
parts due to time or exposure to salt air is specifically 
exempted under this warranty.
    Neither Litex Industries nor the manufacturer will 
assume any liability resulting from improper installation or 
use of this product. In no case shall the company be liable 
for any consequential damages for breach of this, or any 
other warranty expressed or implied whatsoever. This 
limitation as to consequential damages shall not apply in 
states where prohibited.

Summary of Contents for E-DCF52BNK5C3











Reviews: