background image

page 10

Troubleshooting.

Warranty.

Problem: 

Fan fails to operate.

Solutions:

1. Check wall switch to fan.
2. Verify that reverse switch is set completely in 
either direction.
3. Check to be sure fan is wired properly.

Problem: 

Light kit (optional) not lighting.

Solutions:

1. Check wall switch to fan.
2. Check that bulbs are installed correctly.
3. Check to be sure wires in canopy are wired 
properly.
4. Verify that molex connections in switch 
housing are connected properly.

Problem: 

Fan operates but light fails (if 

applicable).

Solutions: 

1. Check that bulbs are installed correctly.
2. Check to be sure wires in canopy are wired 
properly.
3. Verify that molex connections in switch 
housing are connected properly.
4. Replace defective bulbs with same type of 
bulb.

Problem: 

Fan wobbles.

Solutions:

1. Use the balancing kit provided in one of the 
hardware packs. 

If no blade balancing kit is 

provided, please call Customer Support,
1-800-527-1292, to request one.

2. Check to make sure set screw(s) on motor 
housing yoke is (are) tightened securely.
3. Check to be sure set screw on hanging ball is 
tightened securely.

Parts Replacement.

For parts and information, please refer to
"Parts Inventory" on page 2.
Litex Customer Support:

1-800-527-1292

WARNING: 

Failure to disconnect power supply 

prior to troubleshooting any wiring issues may 
result in serious injury.

LITEX LIFETIME LIMITED WARRANTY:
LITEX INDUSTRIES, LTD. warrants this fan to the original 
household purchaser for indoor use under the following 
provisions:
1-YEAR WARRANTY: LITEX INDUSTRIES, LTD. will replace or 
repair any fan which has faulty performance due to a 
defect in material or workmanship. Contact Litex Customer 
Service at 

1-800-527-1292

 to arrange for return of fan. 

Return fan, shipping prepaid, to Litex Industries, Ltd. We will 
repair or ship you a replacement fan, and we will pay the 
return shipping cost.
5-YEAR WARRANTY: LITEX INDUSTRIES, LTD. will repair or 
replace, at no charge to the original purchaser, any fan 
motor that fails to operate satisfactorily when failure 
results from normal use.
RETURN FAN MOTOR ONLY, shipping prepaid, to Litex 
Industries. We will repair or ship purchaser a replacement 
motor and Litex will pay the return shipping cost.
6-YEAR to LIFETIME LIMITED WARRANTY: LITEX 
INDUSTRIES, LTD. will repair the fan, at no charge to the 
original purchaser for labor only, if the fan motor fails to 
operate satisfactorily when failure results from normal use. 
Parts used in the repair will be billed to the purchaser at 
prevailing prices at time of repair.
    The purchaser shall be responsible for all costs incurred 
in the removal, reinstallation and shipping of the product 
for repairs.
    This warranty does not apply when damage from 
mechanical, physical, electrical or water abuse results in 
causing the malfunction. Deterioration of finishes or other 
parts due to time or exposure to salt air is specifically 
exempted under this warranty.
    Neither Litex Industries nor the manufacturer will 
assume any liability resulting from improper installation or 
use of this product. In no case shall the company be liable 
for any consequential damages for breach of this, or any 
other warranty expressed or implied whatsoever. This 
limitation as to consequential damages shall not apply in 
states where prohibited.

PWLI1712

Summary of Contents for VN52












Reviews: