Assembly Instruction
L
ittfinski
D
aten
T
echnik (
LDT
)
8-fold feedback module
with integrated
occupancy detector
from the
Digital-Professional-Series
!
SX-GB-8-B
Part-No.:
320041
>> kit <<
⇒
feedback report via Sx-bus
(
Selectrix®
or
compatible digital central units
)
⇒
short circuit protected
(one automatic fuse on each output)
⇒
up to 1 Ampere load on each output
⇒
feedback address programmable:
from
0
to
103
⇒
release-delay programmable:
from
0
to
2,48 seconds
This product is not a toy! Not suitable for children under 14 years of age! The kit
contains small parts, which should be kept away from children under 3! Improper
use will imply danger of injuring due to sharp edges and tips! Please store this
instruction carefully.
Introduction:
You have purchased the 8 fold feedback module
SX-GB-8
with
integrated detection of track occupancy for your model railway.
The
SX-GB-8
is a high quality product that is supplied within
the assortment of
L
ittfinski
D
aten
T
echnik (
LDT
).
We are wishing you having a good time using this product.
Feedback modules
SX-GB-8
of the
Digital-Professional-
Series
can be operated with your digital model railway without
any problems
.
The
SX-GB-8
is suitable for all
Selectrix®
or
compatible
digital central units
which support the
Sx-bus
by using the
5-poles diode-plug
.
General:
Tools required for the assembly
Please assure that the following tools are available:
•
a small side cutter
•
a mini soldering iron with a small tip
•
solder tin (if possible 0,5mm diameter)
Safety Instructions
•
All electrical and electronic components included in this kit
shall be used on low voltage only by using a tested and
approved voltage transducer (transformer). All components
are sensitive to heat. During soldering the heat shall be
applied for a very short period only.
•
The soldering iron develops up to 400°C. Please keep
continual attention to this tool. Keep sufficient distance to
combustible material. Use a heat resistant pad for this work.
•
This kit consist of small parts, which can be possibly
swallowed from children. Children (especially under 3 years)
shall not participate on the assembly without supervision.
Set-Up:
For the board assembly please follow exact the sequence of
the below
assembly list
. Cross each line off as
done
after
completing the insertion and the soldering of the respective
part.
For the
diodes
please keep special attention to the correct
polarity (marked line for the cathode).
The connector of
tantalum capacitors
marked with "
+
" has to
correspond with the respective marking on the pc-board.
Integrated circuits (IC`s)
are either marked with a half round
notch on one end or a printed point for the correct mounting
position. Push the IC`s into the correct socket assuring that the
notch or the printed point is corresponding to the half-rounded
marking on the pc-board.
Please attend to the sensitivity of the
ICs
to
electrostatic
discharge
, which will cause immediate damage of the IC.
Before touching those components please discharge yourself
by contacting an earthed metal (for example: an earthed
radiator) or work with an electrostatic safety pad.
On
transistors
and
voltage-regulators
it has to be attended
to the flattened side.
The position of the soldered
wire-bridge
is marked on the
board with a thick white line between the respective bores.
Before assembling the clamps please connect the
two
2-pole
and the
two 3-pole clamps
together to a block with
10
connections
.
The
light emitting diodes
have to be assembled on the pc-
board with the longer leg to be connected to "
+
". Before
soldering the diodes push the
distance spacers
onto the legs.
Assembly List:
Pos.
Qty. Component
Remarks
Ref.
Done
1
1
Printed Circuit Board
2
1
Resistor 560 Ohm
green-blue-black-black
R3
3
8
Resistors 1KOhm
brown-black-black-brown
R4..R11
4
4
Resistors 4,7KOhm
yellow-violet-black-brown
R12..R15
5
2
Resistors 22KOhm
red-red-black-red
R16, R17
6
4
Resistors10KOhm
brown-black-black-red
R18..R21
7
9
Resistors 100KOhm
brown-black-black-orange
R22..R30
8
2
Resistors 100Ohm
brown-black-black-black
R31,R32
9
1
Resistor 1MOhm
brown-black-black-yellow
R33
10
3
Wire-bridges
spare wire
Br1..Br3
11
1
Diode BAW 75
attend to the polarity!
D17
12
1
IC-Socket 20-poles
IC1
13
3
IC-Sockets 14-poles
IC4..IC6
14
1
IC-Socket 8-poles
IC2
15
7
Capacitors 100nF
100nF = 104
C1..C7
16
1
Tantalum cap. 0,1uF/35V attend to the polarity!
C8
17
1
Resonator 12MHz
CR1
18
1
Push button
S1
19
16 Diodes BY251
attend to the polarity!
D1..D16
20
1
Transistor BC 557
attend to the polarity!
T1
21
1
Voltage regulator 78L05
attend to the polarity!
IC3
22
1
LED + dist. Spacer
attend to the polarity!
LED1
23
8
Multi-Fuses R090
MF1..8
24
2
Clamps 2-poles
build blocks before assembly
25
2
Clamps 3-poles
build blocks before assembly
26
2
Sockets 5poles
ST1, ST2
27
1
IC: AT89C2051
attend to the polarity!
IC1
28
3
IC: LM339
attend to the polarity!
IC4..IC6
29
1
IC: 24C02
attend to the polarity!
IC2
30
Final Control
Made in Europe by
L
ittfinski
D
aten
T
echnik (
LDT
)
Kleiner Ring 9
D-25492 Heist/Germany
Phone: 0049 4122 / 977 381; Fax: 0049 4122 / 977 382
Internet: http://www.
ldt-infocenter
.com
Subject to technical changes and errors.
05/2013 by LDT
