background image

BEFORE GETTING STARTED

READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL, OPERATE, OR SERVICE YOUR PRODUCT. KNOW THE PRODUCT’S APPLICATION, 
LIMITATIONS, AND POTENTIAL HAZARDS. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH THESE 
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
Refer to product data plate(s) for additional operating instructions and specifications. 

This is the safety alert symbol. When you see this

s

!

symbol on your pump or in this manual, look for one of the following signal words and be alert to the 

potential for personal injury or property damage if ignored: 

s

!

DANGER

 warns about hazards that will cause serious personal injury, death or major property damage if ignored.

s

!

WARNING

 warns about hazards that can cause serious personal injury, death or major property damage if ignored.

s

!

CAUTION

 warns about hazards that will or can cause minor personal injury or major property damage if ignored.

s

!

NOTICE

 indicates special instructions which are important but not related to hazards. Carefully read and follow all safety instructions  

in this manual and on pump.

s

!

DANGER

 DO NOT USE TO PUMP FLAMMABLE OR EXPLOSIVE FLUIDS SUCH AS GASOLINE, FUEL OIL, KEROSENE, ETC. DO NOT USE IN  

EXPLOSIVE ATMOSPHERES OR HAZARDOUS LOCATIONS AS CLASSIFIED BY THE NEC, ANSI/NFPA70. FAILURE TO FOLLOW THIS WARNING CAN RESULT IN  

PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. DO NOT HANDLE A PUMP OR PUMP MOTOR WITH WET HANDS OR WHEN STANDING ON A WET OR  

DAMP SURFACE, OR IN WATER. FAILURE TO FOLLOW THIS WARNING CAN RESULT IN FATAL ELECTRICAL SHOCK. PUMP SHOULD ONLY BE USED WITH  

LIQUIDS COMPATIBLE WITH PUMP COMPONENT MATERIALS.

s

!

WARNING

 Make certain that the unit is disconnected from the power source before attempting to service or remove any 

component. If the power disconnect is out of sight, lock it in the open position and tag it to prevent unexpected application of power.

s

!

WARNING

 This equipment should be installed and serviced by technically qualified personnel. Comply with national and local 

electrical and plumbing codes when installing this unit. Failure to install it in compliance with national and local electrical and plumbing codes and within 

Little Giant’s recommendations may result in electrical shock or fire hazard, unsatisfactory performance, or equipment failure. Installation information  

is available through pump manufacturers and distributors, or directly from Little Giant at our toll-free number, 1-888-956-0000.

This equipment must not be used by children or persons with reduced physical, sensory or mental abilities, or lacking in experience and expertise,  

unless supervised or instructed. Children may not use the equipment, nor may they play with the equipment or in the immediate vicinity.

s

!

CAUTION

 In any installations where property damage and/or personal injury might result from an inoperative or leaking pump due 

to power outages, discharge line blockage, or any other reason, a backup system(s) and/or alarm should be used.

•  Keep work area clean, well-lit, and uncluttered.
•  Keep safety labels clean and in good condition.
•  Do not run pump dry. For optimal cooling and to prolong the  

motor life, the liquid level being pumped should normally  

be above the top of the pump housing.

s

 

CAUTION

!

W A R N I N G

W A R N I N G

•  Wear safety glasses while installing or performing 

maintenance on pump.

•  Make sure all 

ELECTRICAL POWER IS OFF

 before 

connecting any electrical wires.

Summary of Contents for LG-MPA33

























Reviews: