background image

 

14 

                                          CHAPTER 3:    Troubleshooting                                                       

 

3.7 TROUBLESHOOTING - SPEAKER / AUDIO ISSUES       

Speaker / Audio Issues

 

 

1)    SYMPTOM:

 

             

  a. No sound through the speakers but headphones work.     

                b. No sound through headphones but the speakers work.         

                c. No sound through speakers or headphones.     

                d. IPod not charging.     

                e. Speakers buzzing.   

                f. Sound from one speaker only.   

                g. Shock from headphones.       

                     

2)    SOLUTION:

       

         

        a. One of the speaker boards has a bad connection or is faulty.           

                      - Check the connection of the wires going from the speakers to the speaker power board. 

                      - Check the connection of the wires going from the speaker power board to the amp board.     

                      - Check the connection of the wires going from the amp board to the console. 

                      - Replace the speaker or amp boards and wiring.     

                      - Replace the speakers.     

                      - If the speaker board, amp board, wiring, and speakers do not solve the issue,   

replace the console.                 

 

                b. There is a bad connection between the headphones and the console.         

                      - Verify the connection of the music player to the dock or audio adaptor cable.       

                      - Verify the audio adaptor cable connection at the console.     

                      - Replace the headphone jack.     

                      - Replace the audio adaptor cable.     

 

                  c. There is a bad connection between one of the audio boards and the console.     

                      - Verify the connection of the music player to the dock or audio adaptor cable.     

                      - Verify the audio adaptor cable connection at the console.   

                      - Replace the audio adaptor cable.     

                      - Replace the console.     

 

                  d. IPod or IPod dock has a bad connection.     

                      - Verify the connection of the IPod.     

                      - Verify the connection of the IPod dock at the console.     

                      - Replace the IPod dock.     

 

 

Summary of Contents for LSPRO2
















Reviews: