background image

 6. Display Monitor

(1) Display 

1.1  “TIME” window has two modes which shows the running time. 

① 

Forward counting 

time is from 0:00 to 99:59 minutes. 

② 

Countdown is count to 0 from the set time(setting 

range: 5:00~99:00 minutes). The machine will stop slowly when it counts to 0:00 and shows” 

end”, then the machine will come to the standby mode after 5 seconds.                                                               

“STEP” window shows the steps. It counts from 0 to 9999 steps. It will recount when the step 

numbers reaches the top point.

Note: The window will be switched from TIME and STEP cyclically, you can press “M” 

button to switch between cyclic display mode and single display mode in motion state.                                                    

                                                    

1.2 “DISTANCE” 

window has two modes which shows the current movement distance.

 

① 

In the forward counting mode, the distance will be increased from 0.0 to 99.9 miles, it will 

recount if the distance reaches the top point. 

 

In the distance countdown mode, the 

distance will be decreased from the setting data(setting range:1.00~99.00miles) to 0 . The 

machine will stop slowly when it counts to 0:00 and shows” end”, then the machine will come 

to the standby mode after 5 seconds.   

“CALORIES” window has two modes which shows the calories. 

① 

Forward mode counts 

from 0 to 9999, it will recount when it reaches the top point.  

② 

Countdown mode will count 

from setting calorie data( setting ranges 20~990) to 0. The machine will stop slowly when it 

counts to 0:00 and shows” end”, then the machine will come to the standby mode after 5 

seconds.

Note: The window will be switched from DISTANCE and CALORIES cyclically, you can 

press“ M” button to switch between cyclic display mode and single display mode in 

motion state.                                  

1.3 “SPEED” 

 window shows the current running speed, the setting range is 

0.5MPH~6.5MPH. The speed will +/- 0.1MPH every time you click  “+/-” button.  

P1 ~ P12 are displayed under the setting of automatic selection.

1.4  After the treadmill is started, every window will be displayed cyclically at an interval of 

5 seconds. You can press the "M" button to switch between cyclic display mode and single 

display mode.

1.5  The maximum speed of the treadmill will be limited to 4MPH when the dashboard 

deflected from a horizontal direction to an arbitrary direction by more than 60 degrees.

SPEED        DIST.

TIME        CAL.         STEP

Summary of Contents for LINKLIFE Gamma Fitness











Reviews: