background image

2 (15)

EN.33.C.94.1702

Assembly instructions | LK Electric Boiler 11-n

14. Return connector 1” female
15. Cable screwed unions
16. Knock-out opening, to be used when con-

nection cables come out of the wall

17. Overheating (maximum safe temperature) 

protection

18. Main switch
19. LED x 4
20. Circuit board OX 7E
21. Circuit board OX 7E UTK
22. Pressure gauge/thermometer
23. Cover for electric cartridge
24. Shrouds for electrical connections on elec-

tric cartridge

25. Skirt concealing pipe connections

13 14

15

12

23

17

18

22

3

19

25

1 2

5

4

8

7

6

9

16

18 20

17

11

14

13

24

12

22

21

10

Benämning

1.  Safety valve, 2.5 bar, ¾” female
2.  Automatic air-bleeding valve,

 ⅜

” male

3.  Control panel
4.  Boiler tank, incl. electric cartridge
5.  Expansion vessel, 12 litres, pre-pressure 1.5 

bar

6.  Nipple for controlling/filling expansion 

vessel with air

7.  Installation points for temperature and ther-

mometer sensors

8.  Connector for pressure gauge
9.  Circulation pump, 1” male
10. Overflow valve
11. Filling/drainage valve, ½” male 
12. Discharge pipe for safety valve
13. Flow connector 1” female

4

5

6

7

8

9

10

11

12

13 14

22

16

17

18

21

Summary of Contents for 11-n
















Reviews: