background image

9 (15)

EN.33.C.94.1702

Assembly instructions | LK Electric Boiler 11-n

Settings

ON

OFF

ON

OFF

OFF

OFF

ON

OFF

OFF

OFF

ON

ON

ON

OFF

OFF

OFF

16A

20A

25A

35A

50A

OFF

OFF

OFF

OFF

ON

ON

OFF

ON

ON

ON

OFF

7-levels

6-levels

5-levels

4-levels

Main fuses’ rating size.

Supply setting 20A.

Circulation pump’s 

drive mode:

continuous

supply setting 

summertime drive mode

Maximum number of capacity 

levels for the boiler.
Each level corresponds to 

1.6 kW. See following table.
Supply setting 7 levels: 

11 kW.

Fuse

Fuse

Fuse

Fuse

Fuse

Output 

level 

Output  Cur-

rent L1 

Cur-

rent L2

Cur-

rent L3 

Output 

group

kW

A

A

A

1; 15%  1,6 

3,9 

3,9 

2; 30%  3,1 

3,9 

3,9 

7,8 

3; 45%  4,7 

6,8 

6,8 

6,8 

1 + 2 

4; 55%  6,3 

9,1 

9,1 

9,1 

5; 70%  7,9 

13 

13 

9,1 

1 + 3 

6; 85%  9,4 

13 

13 

16,9 

2 + 3 

7; 

100% 

11 

15,9 

15,9 

15,9 

1 + 2 

+ 3 

Remote control: Switch 1 in position ON, see item 

Remote control.

ON

OFF

Remote control

Switch 1 

in position ON

7

Temperature setting in accordance with item 8, 

applies when inlet is open. When inlet is shut, or-

dinary temperature setting applies.

Temperature 

setting when 

regulated via 

remote control

Switching off: Switch 1 in position OFF, see item 

Switching off

.

ON

OFF

Off switch 1

in position OFF

Summary of Contents for 11-n
















Reviews: