background image

INSTRUCTION MANUAL

9

7. Warranty

This product is warranted to be free from defects in material and workmanship for a period of 

three (3) years from date of purchase. 
This warranty is valid only if the product is used for its intended purpose and within the 

guidelines specified in this instruction manual. This warranty does not cover damage caused 

by accident, neglect, misuse, improper service, natural forces or other causes not arising 

from defects in original material or workmanship. This warranty does not cover any incidental 

or consequential damages, commercial loss or any other damagesfrom the use of this 

product.

The warranty does not cover damage to paint or finish and defects or damages caused by 

physical and chemical abuse or normal wear and tear. The warranty is invalidated by any non-

factory modification, which will immediately terminate all liabilities on us for the products or 

damages caused by its use. The buyer and its customer shall be responsible for the product 

or use of products as well as any supervision required for safety. If requested the products 

must be returned to the distributor in well packed and insured manner and all shipping 

charges must be paid.

Information on the disposal of electrical and electronic devices in the European Community:
The disposal of electrical devices is regulated within the European Community by national 

regulations based on the European Directive 2012/19/EU on waste electrical and electronic 

equipment (WEEE). According to these regulations, any devices supplied after 13.06.05 in the 

business to business sphere, to which this product is assigned, may no longer be disposed of 

in municipal or domestic waste. They are marked with the following symbol to indicate this. 

As disposal regulations within the EU may vary from country to country, please contact your 

supplier if necessary.

PRODUCT DISPOSAL

 

In case the product is to be disposed of, the relevant legal regulations are to be followed.

                           

 

Summary of Contents for uniPERISTALTICPUMP 3













Reviews: