C H A P T E R 3 : P R O C E D U R E S
QUICK LOAD SERVO 65/80
3 - 1 7
Calibration of the Loading Table
Whenever the diameter or the profile is changed, the centerline of the loading table is automatically
adjusted according to the parameters entered by the operator.
If, for any reason whatsoever, the centerline of the loading table would be incorrect (either too low or too
high), it can be corrected.
Conditions:
-
Bars on the magazine.
-
Loading table in lower position.
-
Bar feed in
STOP
mode.
Procedure:
Step 1:
Press on the key corresponding to
[MANUAL MODE]
.
Step 2:
Press on
[F2]
to move up the loading table in upper position. The bar now faces the spindle of the lathe.
Press the
[STOP]
key.
Step 3:
In the main menu, select the menu
[SERVICE]
with the up/down keys, then press on the key
corresponding to
[ENTER]
.
Step 4:
In the service menu, select the menu
[BAR FEED SETUP]
, then press on the key corresponding to
[ENTER]
.
Step 5:
Press on the key corresponding to
[PAGE DOWN]
until the text "
NUMBER OF PULSES FOR TABLE
CENTERING CALIBRATION
". Press on any arrow key.
Step 6:
Enter with the up/down and left/right keys the password
[2534]
, then press on the key corresponding to
[ENTER]
.
Step 7:
Enter with the up/down keys to modify the centerline of the loading table. One pulse is approx. 0,4 mm of
vertical displacement.
Examples:
Step 8:
[10]
= vertical displacement of approx. 4 mm upwards.
[ -5]
= vertical displacement of approx. 2 mm downwards.
Once the right value has been entered, press on the key corresponding to
[ENTER]
to confirm.
Step 9:
Press on the key corresponding to
[ESC]
to exit the menu.
Step 10: Press on the
[F3]
key to move down the loading table.
Step 11: Press on the
[F2]
key to move up the loading table. The correction of the loading table has been taken into
account.
Procedure complete.
Summary of Contents for Quick Load Servo 65
