background image

FCC Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 

conditions: (1) This device may not cause harmful interference, and (2) this device must accept 

any interference received, including interference that may cause undesired operation.

NOTE 1:

 This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec-

tion against harmful interference in a residential installation. This equipment generates, uses 

and can radiate radio frequency energy and, if not installed and used in accordance with the 

instructions, may cause harmful interference to radio communications. However, there is no 

guarantee that interference will not occur in a particular installation. If this equipment does cause 

harmful interference to radio or television reception, which can be determined by turning the 

equipment off and on, the user is encouraged to try to correct the interference by one or more 

of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected.

- Consult the dealer or an experienced radio/TV technician for help.

NOTE 2:

 Any changes or modifications to this unit not expressly approved by the party responsible 

for compliance could void the user's authority to operate the equipment.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled 

environment. It should be installed and operated with minimum distance 20cm between the 

radiator & your body.

IC WARNING

This device contains licence-exempt transmitter(s) that comply with Innovation, Science and 

Economic Development Canada’s licence-exempt RSS(s).  Operation is subject to the following 

two conditions: 

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired 

operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux 

CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils 

radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:

1. L’appareil ne doit pas produire de brouillage;

2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est suscepti-

ble d’en compromettre le fonctionnement.

IC Radiation Exposure Statement

This equipment meets the exemption from the routine evaluation limits in section 2.5 of RSS-102. It 

should be installed and operated with a minimum distance of 20cm between the radiator and 

any part of your body.

 

Cet équipement est conforme à l'exemption des limites d'évaluation habituelle de la section 2.5 

de la norme RSS-102. Il doit être installé et utilisé à une distance minimale de 20 cm entre le 

radiateur et toute partie de votre corps

WARNING:

 This product can expose you to chemicals including Lead, which is known to the 

State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.

Summary of Contents for 238SL















Reviews: