background image

E2620 Auxilliary Power Unit User Guide

Detailed Description

The Auxilliary Power Unit or APU is housed in a rectangular 
modular aluminum enclosure which is black anodized for 

protection against corrosion, and to help with heat dissipation.  
This unit includes a battery cable, a 40A battery guard, a 600W 

inverter, a 25A battery charger, a fan controller, and a connector 
to the battery monitor.  

Power Input

Battery power at a nominal 12V enters the unit via the battery 
cable to a terminal block, which is a common connection point for

the other system components.  

Battery Guard

The battery guard is a protective switch between the battery and 

the inverter which is normally on when the input battery voltage 
is above a programmed threshold.  Once the battery voltage 

drops below this threshold, the switch is turned off so the inverter
load does not discharge the battery any further in order to protect

the battery against excessive discharge which would adversely 
affect its lifetime.  The battery guard is limited to a 40A load 

which represents a ~400W maximum load at the inverter output.  
Loads greater than 400W will cause the battery guard to 

shutdown until the overload is removed.  The battery guard is 
enabled on or off by the battery monitor.

Inverter

The inverter converts the 12VDC battery power to a 120VAC pure 
sine wave output through two standard 120VAC outlets.  A USB 

port is also available to power or recharge 5V USB devices.  The 
output power rating is up to 600W continuous although the 

5

This device is not authorized for use with any product where the failure or malfunction of 
this device can reasonably be expected to cause injury or death.  This device is not 
authorized for use in any life support system due to the risk of injury or death.

Summary of Contents for E2620













Reviews: