background image

E2620 Auxilliary Power Unit User Guide

Location

The APU should be mounted in a horizontal position and 
protected from the elements and out of the way.  The unit can be 

mounted on a shelf with a retainer to prevent it from being 
dislodged while in motion. The unit mount should also include 

drain holes to prevent any water from accumulating.  

Cooling Considerations

The airflow is from the rear intake louvers (at the sides) to the 

front exhaust louvers, so a generous airspace over one inch 
should be allowed for around both the intake and the exhaust 

louvers as well as a straight and unimpeded access to open air.  
The mount should not restrict or contain the air otherwise the 

inverter will shut down due to excessive heat buildup. 

Connections

Equipment power plugs can be plugged into the inverter, and the 

access door closed to prevent any rain or snow from entering the 
unit.  The equipment power cables can be restrained with VELCRO

hook and loop fastener straps.  The battery monitor should be 
located where the operator can see the display and warning LEDs,

as well as operate the power switch.  The battery monitor cable is 
connected to the unit within the access door.  It is a keyed twist 

and turn connector.

Battery

The battery should be selected for capacity while considering the 

weight.  The battery should be mounted such that the battery 
cable is free to move without strain.  The battery cable is supplied 

with a mating high power connector and fused leads for the 
battery.  The mating connector needs to be attached to the 

battery enclosure in a manner that prevents rain entry.

8

This device is not authorized for use with any product where the failure or malfunction of 
this device can reasonably be expected to cause injury or death.  This device is not 
authorized for use in any life support system due to the risk of injury or death.

Summary of Contents for E2620













Reviews: