Abgleichfunktion
Alignment functions
Anzeige - Bildschirm z.B.
Display - Screen e.g.
Einstellwerte / Besonderheiten
Settings / special features
14a
14b
15
16
Cutoff
Red
xxx
Green
xxx
White drive
Red
xxx
Green
xxx
Blue
xxx
Option bytes
Achtung!
Hier nur Eingaben machen und Speicherung vornehmen
a) im notwendigen Reparaturfall
b) bei gewünschten Programm-/Normänderung:
Abgleichart siehe Option Bytes Tabelle
Caution!
Here inputs and memorizing:
a) in the event of necessary repairs
b) if you wish to alter programs/norms
For alignment method see Option Bytes Table
5. Abgleichfunktionen (13-16)
5. Alignment functions (13-16)
Cutoff-Meßimpuls
Cutoff Measuring Pulse
An den Farbendstufen messen (MP 1,2,3), welche die höchste Spannung zeigt. Mit Ug2-Regler im DST oder
Reglerblock einstellen: Cutoff = 148
±
2,5V DC (für Aconda 93102 Cutoff = 158
±
2,5V) [Vor dieser Einstellung
muß Kontrast auf 50, Helligkeit auf 23, Farbsättigung auf 32, Schärfe auf 3 und DNR auf EIN eingestellt werden.
Für alle 2 Farben muß Cutoff auf 10 und Weißwert (14) auf 32 stehen! Für 16:9 Geräte muß 16:9 eingeschaltet
sein.]
Measure the colour output stages (MP 1,2,3) to see which
shows the highest tension. With the Ug2 adjuster in DST
or adjusting pad, make the following setting: cutoff = 148
±
2.5 V DC
(at Aconda 93102 Cutoff = 158
±
2,5V) [before making this setting, the
contrast must be set to 50, brightness to 23, colour saturation to 32,
sharpness to 3 and DNR to ON). For both colours, the cutoff
must be 10 and white level (14) must be 32! Regarding 16:9 sets,
the 16:9 feature must be activated.]
Cutoff-Referenzwert
Cutoff Reference Value
Weißwert
White Level
Cutoff
Red
xxx
Green
xxx
Blue
xxx
Option byte 0 - 8
Bit 7 6 5 4 3 2 1 0
x x x x x x x x
In der Weißfläche die beiden schwachen Farben soweit erhöhen, bis Normweiß erscheint,
jeweils Werte mit Taste ”OK” abspeichern. Im VGA-Modus ist Abgleich mit VGA-Testbild zu wiederholen.
Increase both faint colours in the white surface until standard white appears and save each setting
by pressing “OK”. Adjustment with VGA test picture must be repeated in VGA mode.
In der Graufläche die beiden fehlenden Farben soweit erhöhen, bis Normschwarz erscheint,
anschließend mit Taste ”OK” abspeichern. Im VGA-Modus ist Abgleich mit VGA-Testbild zu wiederholen.
In the grey area rise the missing two colours until black becomes standard, then store these values
with ”OK” key. Adjustment with VGA test picture must be repeated in VGA mode.
13
Bildaustastlücke (0,1msec)
vert. blanking period (0.1msec)
CUT OFF
Schwarzwert
black level
0 V
Horizontal Offset
Geometrie
H Offset
xxx
Bild auf Mittelposition abgleichen, d. h. der Rand auf beiden Seiten soll gleiche Breite haben.
Adjust the picture to the centre position, i.e. the edge should have the same width on both sides.
1 - 26
Summary of Contents for Vitros 6381 ZW
Page 114: ...3 39...