background image

LOFTNESS SPECIALIZED EQUIPMENT, INC. 

LIMITED WARRANTY POLICY

 

The limited warranty policy begins upon delivery of the unit to the original customers. 
All Loftness products have a one (1) year limited warranty.  The XLB10 Grain Bag Loader has a two (2) year limited warranty. 
If any Loftness product is used as rental equipment, or in a commercial application, the limited warranty period is for only 30 days 

from the delivery date to the original customers. 
Loftness Specialized Equipment, hereinafter referred to as LOFTNESS, a manufacturer of quality machinery since 1956, warrants 

new LOFTNESS machinery and/or attachments at the time of delivery to the original purchaser, to be free from defects in material and 

workmanship when properly set up and operated in accordance with the recommendations set forth in the LOFTNESS Operator’s 

Manual. 
LOFTNESS’ liability for any defect with respect to accepted goods shall be limited to repairing the goods at an authorized dealer or 

other  LOFTNESS  designated  location,  or  replacing  them  as  LOFTNESS  shall  elect.    The  above  shall  be  in  accordance  with 

LOFTNESS warranty adjustment policies. 

WARRANTY REQUIREMENTS 

  .

s

m

i

a

l

c

 

y

t

n

a

r

r

a

w

 l

l

a

 

e

t

a

d

il

a

v

 

o

t

n

e

m

p

i

u

q

E

 

d

e

z

il

a

i

c

e

p

S

 s

s

e

n

tf

o

L

 

o

d

e

n

r

u

t

e

r

 

d

n

a

 t

u

o

 

d

e

ll

if

 

e

b

 t

s

u

m

 

m

r

o

n

o

it

a

r

t

s

i

g

e

r

 

y

t

n

a

r

r

a

W

To receive a warranty claim, a return authorization from LOFTNESS must be obtained.   The failed part may then be returned in an 

  .

g

n

i

c

i

v

r

e

s

 r

o

f

 

y

r

e

n

i

h

c

a

m

 

g

n

i

n

r

u

t

e

r

 

n

e

h

w

 

d

e

r

r

u

c

n

i

 s

e

g

r

a

h

c

 

y

r

e

v

il

e

d

 r

o

 t

h

g

i

e

r

f

 

e

d

u

l

c

n

i

 t

o

n

 s

e

o

d

 

y

t

n

a

r

r

a

w

 s

i

h

T

 

 .

s

u

t

a

t

s

 

d

e

r

e

p

m

a

t

n

u

Dealer mileage, service calls and pick-up/delivery charges are the customer’s responsibility.

 

LIMITATIONS OF WARRANTY 

LOFTNESS  products  are  designed  to  provide  years  of  dependable  service  when  proper  use  and  maintenance  is  adhered  to.   The 

potential for misuse in many applications exists; therefore, a limited warranty is provided as follows. 
This warranty shall not apply to any machine or attachment which shall have been repaired or altered outside the LOFTNESS factory 

or authorized LOFTNESS dealership or in any way so as in LOFTNESS’ judgment, to affect its stability or reliability, nor which has 

been subject to misuse, negligence or accident, nor to any machine or attachment which shall not have been operated in accordance 

with LOFTNESS’ printed instructions or beyond the company recommended machine rated capacity.  LOFTNESS may elect to have 

an area representative evaluate the condition of the machine before warranty is considered. 
In addition, this limited warranty provides no coverage for general wear or maintenance items, misuse, environmental conditions and/

or contamination for which they were not designed or not intended, including but not limited to the following items: 

Use of machine beyond its rated capacity; 

Improper knife replacement; 

Missing knives; 

Striking foreign objects 

Lack of lubrication 

Failures caused by running in an “out-of-balance” condition; 

Tires; 

Conveyors; 

Auger wear; 

Saw blades; and  

Brakes and brake pads. 

EXCLUSIONS OF WARRANTY

 

Except as otherwise expressly stated herein, LOFTNESS makes no representation or warranty of any kind, expressed or implied. 

 The 

implied  warranty  of  merchantability  and  fitness  for  a  particular  purpose  are  excluded  from  this  limited  warranty.

    The 

remedies set forth in this warranty are the only remedies available to any person under this warranty.   LOFTNESS shall have no 

liability to any person for incidental, consequential or special damages of any description, whether arising out of express or implied 

warranty or any other contract, negligence, or other tort or otherwise.  This exclusion of consequential, incidental and special damages 

is independent from and shall survive any finding that the exclusive remedy failed of its essential purpose.  Upon purchase, the buyer 

assumes all liability, all personal injury and property damage resulting from the handling, possession or use of the goods by the buyer. 
No  agent,  employee  or  representative  of  LOFTNESS  has  any  authority  to  bind  LOFTNESS  to  any  affirmation,  representation  or 

warranty concerning its machinery and/or attachments except as specifically set forth herein. 
April 2017

Summary of Contents for OS 170













































































Reviews: