Features and Parts Listings
D.O.C. NOTICE:
The Canadian Department of Communications label identifies certified equipment. The certification means that the equipment
meets certain telecommunications network protective, operational and safety requirements. The Department does not guarantee
the equipment will operate to the user’s satisfaction.
Before installing this equipment, user should ensure that it is permissible to connect to the facilities of the local
telecommunications company. The equipment must also be installed using an acceptable method of connection. User should
ensure that the telephone lines and metallic water pipe system (if present) are electrically grounded.
The TeleDoorBell is a telephone based doorbell system that provides the system user with the capability of communicating with a
door speaker from any installed telephone set, including cordless. Unmatched in convenience, this unique new product provides
the following features:
* System will work as a replacement or in parallel with any standard doorbell. (see page 7)
* Provides high-quality audio conversation capability with any connected Door Station Speaker.
* Unique telephone ringing when Door Station Speaker button pressed. (see page 8)
* Allows user to activate a Door Station Speaker by entering a unique touch-tone code from any telephone. (see page 13)
* Will provide call restriction at the discretion of the owner. (see page 8)
* Relays available for doorbell chime activation or any other devices (24Volts 1Amp max rating).
* Door Station Speaker has LED illuminated Button.
* The system gives a user two minutes to access the Door Station Speaker once the speaker button has been pressed.
* Door Station Speaker Call Waiting function which allows the user to switch between a Visitor and an existing Phone Caller.
The user can press
on a touch-tone telephone to put the telephone call on hold and connect to the Door Station
Speaker. Pressing
again will return the User back to existing Caller. Note: this can only be used once the Door Station
Speaker button is pressed. A second option for switching from Caller to Visitor is by hanging up on the existing telephone
call and then picking up the handset (within the allowed 2 minutes) at which point you will be automatically connected to the
Door Station Speaker.
(Beyond the two minute window you will have to manually activate the Door Station Speaker (
(Door Station Speaker
#1) ...
(Door Station Speaker #4)
(Note: Speaker must be connected to a the port which you are trying to communicate with.)
* Relay closure activated by DTMF digit (Normally Open Dry Contact Operation):
Each RELAY can be triggered for either LATCHING MODE or TIMER MODE (01 - 98 seconds). Default setting is
seconds.
Timer Relays
(Relay #1),
(Relay #2),
(Relay #3 when applicable),
(Relay #4 when applicable),
*
Will activate the relay which is connected to the door station which initiated communication.
Latching Relays
(Relay #1),
(Relay #2),
(Relay #3 when applicable),
(Relay #4 when applicable),
To De-activate latched relays
(Relay #1),
(Relay #2),
(Relay #3 when applicable),
(Relay #4 when applicable),
* Call Restriction blocking (up 10 programmable phone number restrictions) [30 digits maximum / phone number].
* "Door Station Caller ID Display" feature is available when ENABLED and to be used with Call Display Phones only. An
identification information is transmitted by the controller to the display phone when the Door Station Speaker Button is
pressed. Display will show (DOOR 1 ... DOOR 4) which ever speaker port was pressed
* 4-Digit passcode protection for programming system.
* Unit contains E Memory Technology for retaining stored memory data in the event of a temporary power failure.
The TeleDoorBell “X Series” system is shipped from the factory with the following components:
* TeleDoorBell “X Series” control unit
* One (1) Door Station Speaker
* CSA/UL approved class 2 power supply, input 120VAC, 60Hz, output 16VAC 250 mA.
* One (1) RJ31X/CA 38A Jack.
* Two (2) modular RJ-11 Male open-ended patch cord. Used to splice and connect Door Station Speaker and Relay, and
built in door chime relay.
* RJ-45 8 pin male to male modular patch cord 36" long.
* Two (2) #8 screws 1" for mounting Door Station Speaker
* Two (2) plastic anchors for mounting Door Station Speaker
* One (1) #6 wood screw 2" for mounting Controller
* Dimensions: Controller (17cmX17cmX4cm) Door-speaker (17cmX11cmX3.3cm)
*4
*4
*#1
*#4
#11
#21
#31
#41
#51
#19
#29
#39
#49
#10
#20
#30
#40
6
Parts list
2
Features and Instructions Overview
Page 4
