24
This section shows the visibility distance according to the device’s location inputted into ProWeatherLive
(PWL). If you have optional PM2.5/PM10 air quality sensor(s), you can also view the corresponding data
in this section.
AIR QUALITY
UV index shows the current UV index detected by the outdoor sensor.
Air visibility is measured in distance (either in kilometers or miles) and is generally refer to the
distance at which an object or light can be clearly discerned, and it depends on the transparency of the
surrounding air.
NOTE: If the Wi-Fi connectivity is not stable for over three (3) hours, the air visibility will not
appear on the display and the icon will disappear.
This console supports up to four (4) optional PM2.5/PM10 air quality sensors for you to detect different
area's air quality. When you pair this sensor, you can press the AIR QUALITY button to check the readings
in the following display sequence: Visibility > CH1 > CH2 > CH3 > CH4 PM2.5/PM10 sensor's reading.
To activate the auto-loop function in this section, just press and hold the AIR QUALITY button for two (2)
seconds and the
icon will show near the CH number and display the connected channels' reading at
four (4) seconds interval.
The PM2.5/PM10 sensor displays reading in PM2.5 by default. However, users can press the SET UNIT
button to change readings in the following display sequence: PM2.5 > PM10 > PM2.5 AQI > PM10 AQI.
NOTE: The PM2.5/PM10 sensor is an optional sensor, which is not included
UV Index Mode
Visibility Mode
Additional PM2.5/PM10 Air Quality Sensors (Optional)
Activate the Auto Loop for Air Quality
Select the Air Quality Reading Unit
22
4.3.10 RAIN
The
RAINFALL
section shows the rainfall or rain rate information .
4.3.10.1 THE RAINFALL DISPLAY MODE
Press
[ RAIN ]
key to toggle between:
1. RATE
- Current rainfall rate (base on 10 min rain data)
2. HOURLY
- the total rainfall in the past hour
3. DAILY
- the total rainfall from midnight (default)
4. WEEKLY
- the total rainfall of the current week
5. MONTHLY
- the total rainfall of the current calendar month
6. TOTAL
- the total rainfall since the last reset
Period of rainfall
4.3.10.2 TO RESET THE TOTAL RAINFALL RECORD
In normal mode, press and hold
[ RAIN ]
key for 2 seconds to reset all the rainfall record .
NOTE:
Erroneous readings may occur during the installation of the 7-in-1 sensor array . Once the
installation is completed and functioning correctly, it’s advisable to clear all the data and start
afresh .
4.3.11 LIGHT INTENSITY, UV INDEX & SUNBURN TIME
This section of display show the sunlight intensity, UV index and sunburn time .
4.3.11.1 SOLAR LIGHT INTENSITY & SUNBURN TIME MODE:
During solar light intensity mode, press
[ SUN ]
key to switch between sunlight
intensity and sunburn time .
Solar light intensity mode
Sunburn time mode
UV INDEX VS SUNBURN TIME TABLE
Exposure level
Low
Moderate
High
Very high
Extreme
UV index
1
2
3
4
5
6
7
8
9
10
11
12~16
Sunburn time
N/A
45 minutes
30 minutes
15 minutes
10 minutes
Recommended
protection
N/A
Moderate or high UV level! Suggest to
wear sunglasses, broad brim hat and
long-sleeved clothing.
Very high or Extreme UV level! Suggest to
wear sunglasses, broad brim hat and long-
sleeved clothing, If you have to stay outdoors,
make sure to seek shade .
NOTE:
-
The sunburn time is based on normal skin type, it is just a reference of UV strength. In general, the darker
one's skin is, the longer (or more radiation) it takes to affect the skin.
-The light intensity function is for sunlight detection .
4.3.11.2 UV INDEX MODE
To show the current UV index detected by the outdoor sensor .
23
4.3.12 AIR QUALITY
Air quality section shows the visibility distance according to the device location input in PWL. If
you have optional PM2.5/10 sensor(s), you can also view the corresponding data in this section.
4.3.12.1 VISIBILITY MODE
Air visibility is measured in distance (either in km or miles),
and is generally refer to the distance at which an object or light
can be clearly discerned, and it depends on the transparency
of the surrounding air. Visibility range can reach over 50km on
exceptionally clear day, down to under 1km on hazy day .
If the WI-FI connectivity is not stable for over 3 hours, the air
visibility will not be shown, and the
icon will disappear .
4.3.12.2 PM2.5/10 MODE (OPTIONAL SENSOR)
This console supports up to 4 optional PM2 .5 /10 sensors
for you to detect different area's air quality . If you paired this
sensor, you can press the
[ AIR QUALITY ]
key to check the
readings in the following display sequence: Visibility CH1
CH2 CH3 CH4 PM2 .5/10 sensor's reading .
4.3.12.3 ACTIVATE THE AUTO LOOP IN AIR QUALITY SECTION
To activate the auto-loop function in this section, just press and hold the
[AIR QUALITY]
key for
2 seconds and the icon will show near the CH number and display the connected channels'
reading at 4 seconds interval.
4.3.12.4 VIEW DIFFERENT READING OF PM2.5 / 10
The PM2.5 /10 sensor has default display in PM2.5. However, user may press
[ UNIT ]
key to
change readings in the following display sequence: PM2 .5 PM10 PM2 .5 AQI PM10
AQI .
NOTE:
The PM2 .5 / 10 sensor is optional sensor, which is not included .
4.3.13 SKY CONDITION
Sky condition section show the % of cloud cover according to the device location input in PWL. If
you have optional lightning sensor, you can also view the lightnings detected instantly.
4.3.13.1 CLOUD COVER MODE
Cloud cover is an important component of understanding and
predicting the weather. Not only does cloud cover impact sky
conditions and inform precipitation predictions, it also helps regulate
the temperature that occurs in a region .
If the WI-FI connectivity is not stable for over 3 hours, the cloud
cover will not be shown, and the
icon will disappear .
23
4.3.12 AIR QUALITY
Air quality section shows the visibility distance according to the device location input in PWL. If
you have optional PM2.5/10 sensor(s), you can also view the corresponding data in this section.
4.3.12.1 VISIBILITY MODE
Air visibility is measured in distance (either in km or miles),
and is generally refer to the distance at which an object or light
can be clearly discerned, and it depends on the transparency
of the surrounding air. Visibility range can reach over 50km on
exceptionally clear day, down to under 1km on hazy day .
If the WI-FI connectivity is not stable for over 3 hours, the air
visibility will not be shown, and the
icon will disappear .
4.3.12.2 PM2.5/10 MODE (OPTIONAL SENSOR)
This console supports up to 4 optional PM2 .5 /10 sensors
for you to detect different area's air quality . If you paired this
sensor, you can press the
[ AIR QUALITY ]
key to check the
readings in the following display sequence: Visibility CH1
CH2 CH3 CH4 PM2 .5/10 sensor's reading .
4.3.12.3 ACTIVATE THE AUTO LOOP IN AIR QUALITY SECTION
To activate the auto-loop function in this section, just press and hold the
[AIR QUALITY]
key for
2 seconds and the icon will show near the CH number and display the connected channels'
reading at 4 seconds interval.
4.3.12.4 VIEW DIFFERENT READING OF PM2.5 / 10
The PM2.5 /10 sensor has default display in PM2.5. However, user may press
[ UNIT ]
key to
change readings in the following display sequence: PM2 .5 PM10 PM2 .5 AQI PM10
AQI .
NOTE:
The PM2 .5 / 10 sensor is optional sensor, which is not included .
4.3.13 SKY CONDITION
Sky condition section show the % of cloud cover according to the device location input in PWL. If
you have optional lightning sensor, you can also view the lightnings detected instantly.
4.3.13.1 CLOUD COVER MODE
Cloud cover is an important component of understanding and
predicting the weather. Not only does cloud cover impact sky
conditions and inform precipitation predictions, it also helps regulate
the temperature that occurs in a region .
If the WI-FI connectivity is not stable for over 3 hours, the cloud
cover will not be shown, and the
icon will disappear .
23
4.3.12 AIR QUALITY
Air quality section shows the visibility distance according to the device location input in PWL. If
you have optional PM2.5/10 sensor(s), you can also view the corresponding data in this section.
4.3.12.1 VISIBILITY MODE
Air visibility is measured in distance (either in km or miles),
and is generally refer to the distance at which an object or light
can be clearly discerned, and it depends on the transparency
of the surrounding air. Visibility range can reach over 50km on
exceptionally clear day, down to under 1km on hazy day .
If the WI-FI connectivity is not stable for over 3 hours, the air
visibility will not be shown, and the
icon will disappear .
4.3.12.2 PM2.5/10 MODE (OPTIONAL SENSOR)
This console supports up to 4 optional PM2 .5 /10 sensors
for you to detect different area's air quality . If you paired this
sensor, you can press the
[ AIR QUALITY ]
key to check the
readings in the following display sequence: Visibility CH1
CH2 CH3 CH4 PM2 .5/10 sensor's reading .
4.3.12.3 ACTIVATE THE AUTO LOOP IN AIR QUALITY SECTION
To activate the auto-loop function in this section, just press and hold the
[AIR QUALITY]
key for
2 seconds and the icon will show near the CH number and display the connected channels'
reading at 4 seconds interval.
4.3.12.4 VIEW DIFFERENT READING OF PM2.5 / 10
The PM2.5 /10 sensor has default display in PM2.5. However, user may press
[ UNIT ]
key to
change readings in the following display sequence: PM2 .5 PM10 PM2 .5 AQI PM10
AQI .
NOTE:
The PM2 .5 / 10 sensor is optional sensor, which is not included .
4.3.13 SKY CONDITION
Sky condition section show the % of cloud cover according to the device location input in PWL. If
you have optional lightning sensor, you can also view the lightnings detected instantly.
4.3.13.1 CLOUD COVER MODE
Cloud cover is an important component of understanding and
predicting the weather. Not only does cloud cover impact sky
conditions and inform precipitation predictions, it also helps regulate
the temperature that occurs in a region .
If the WI-FI connectivity is not stable for over 3 hours, the cloud
cover will not be shown, and the
icon will disappear .
19
4.3.5.2 INDOOR TEMPERATURE & HUMIDITY
The indoor reading is default mode of the
console, which shows the temperature and
humidity reading of indoor .
4.3.6 MULTI-CHANNEL AND SCROLL MODE FOR OPTIONAL SENSORS
You can add up to 7 additional Thermo-
Hygrometer sensor (optional, refer to
section
3.2
). Press the
[ CH ]
key to switch between
indoor and Channels 1 to 7 .
For auto-scroll function, just press and hold the
[ CH ]
key for 3 seconds and the icon will
appear next to CH. The console will scroll the readings of all the sensors every 3 seconds.
This mode shown below information:
-Channel number of the current sensor
-Temperature and humidity reading of this sensor
-Signal strength of this sensor .
-Sensor type icon (for water pool or soil moisture sensor)
4.3.7 WATER LEAK (OPTIONAL LEAK SENSOR)
You can add up to 7 additional Water Leak sensors (optional, refer
to
section 3.2
)
The channel number(s) of the corresponding water leak sensor(s)
added to the console will be shown with the NO LEAKING icon .
When water leaking is detected, the channel number of the sensor
detecting the leaking will flash together the LEAKING icon.
NOTE:
When low battery is detected, the channel number of the sensor detecting the low battery
condition will flash once ever
y 4 seconds .
4.3.8 WIND
4.3.8.1 WIND SPEED AND DIRECTION SECTION OVERVIEW
Wind direction
Real time wind
direction indicator
Past wind directions
indicator of last 5
minutes (maximum 6)
Average / Gust
Wind speed or
Beaufort scale
Wind speed
level indicator
A solid arrow indicates the current real-time wind direction, whereas the bars indicate up to six
different wind direction of the past 5 minutes .