35
Follow the steps below to update your device’s Function or Wi-Fi
®
System Firmware
1. Download the latest version of the firmware (Function or Wi-Fi
®
) and save it to your PC. Remember
where you saved the file.
2. Set the console into AP (access point) mode then connect the PC/Mac to the console (refer to Setting
Up Wi-Fi
®
Connection).
3. On the SETUP page, press “Advanced” to enter advance setting.
4. Under the firmware upload section, press to locate the firmware file saved on your PC/
Mac.
5. Press to start firmware update.
6. The console will restart once the update completes.
7. The console will stay in AP mode for you to check the firmware version and all the current setting.
Simply press and hold SENSOR/WIFI button for six (6) seconds to exit AP mode.
NOTES: You cannot update the Function Firmware and Wi-Fi
®
Firmware at the same time. Updates
must be installed one by one.
Make sure the power cable remains connected during the update process.
Make sure your PC’s wireless connection is stable.
Once the update process starts, do not try to do anything else on your PC or on the display console.
29
8.1.1 FIRMWARE UPDATE STEP
1.
Download the latest version firmware to your PC/Mac.
2. Set the console into AP (access point) mode then connect the PC/Mac to the console (refer
to
section 6.1
and
6.2
).
3.
From the SETUP page, press ADVANCED to enter advance setting
4.
Under the firmware upload section, press
Browse
to locate the firmware file saved on
your PC/Mac.
5. Press
Upload
to start firmware update.
The update time is around 5 ~ 10 minutes. While updating, the
progress will be displayed (i.e. 100 is completion).
6. The console will restart once the update is completed.
7. The console will stay in
AP mode
for you to check the firmware version and all the current
setting. Simply press and hold
[ SENSOR / WI-FI ]
key for 6 seconds to exit AP mode.
IMPORTANT NOTE:
-
Please keep connecting the power during the firmware update process.
-Please make sure your PC/Mac's WI-FI connection is stable.
-
When the update process start, do not operate the PC/Mac and console until the update finished.
-
During firmware update the console will stop upload data to the cloud server. It will reconnect to your WI-FI
router and upload the data again once the firmware update succeed. If the console cannot connect to your
router, please enter the SETUP page to setup again.
-
After the firmware update, If the setup informations are missing, please input the setup information again.
-
Firmware update process have potential risk, which cannot guarantee 100% success. If the update fail,
please redo the above step to update again.
8.2
BATTERY REPLACEMENT
When low battery indicator “ ” is displayed near the antenna icon
of the sensor(s), it indicates that the outdoor 7-IN-1 sensor and/or
current channel sensor(s) battery power is low respectively. Please
replace with new batteries.
8.2.1 RE-PAIRING THE SENSOR(S) MANUALLY
Whenever you changed the batteries of the 7-in-1 weather sensor array or other additional
sensors, re-synchronization must be done manually.
1. Change all the batteries to new ones in the low battery sensor(s).
2. Press
[ SENSOR / WI-FI ]
key on the console to enter sensor synchronization mode (as
indicated by the flashing antenna
).
8.3
RESET AND FACTORY RESET
To reset the console and start again, press the
[ RESET ]
key
once or remove the backup battery
and then unplug the adapter.
To resume factory settings and remove all data, press and hold the
[ RESET ]
key for 6 seconds.
29
8.1.1 FIRMWARE UPDATE STEP
1.
Download the latest version firmware to your PC/Mac.
2. Set the console into AP (access point) mode then connect the PC/Mac to the console (refer
to
section 6.1
and
6.2
).
3.
From the SETUP page, press ADVANCED to enter advance setting
4.
Under the firmware upload section, press
Browse
to locate the firmware file saved on
your PC/Mac.
5. Press
Upload
to start firmware update.
The update time is around 5 ~ 10 minutes. While updating, the
progress will be displayed (i.e. 100 is completion).
6. The console will restart once the update is completed.
7. The console will stay in
AP mode
for you to check the firmware version and all the current
setting. Simply press and hold
[ SENSOR / WI-FI ]
key for 6 seconds to exit AP mode.
IMPORTANT NOTE:
-
Please keep connecting the power during the firmware update process.
-Please make sure your PC/Mac's WI-FI connection is stable.
-
When the update process start, do not operate the PC/Mac and console until the update finished.
-
During firmware update the console will stop upload data to the cloud server. It will reconnect to your WI-FI
router and upload the data again once the firmware update succeed. If the console cannot connect to your
router, please enter the SETUP page to setup again.
-
After the firmware update, If the setup informations are missing, please input the setup information again.
-
Firmware update process have potential risk, which cannot guarantee 100% success. If the update fail,
please redo the above step to update again.
8.2
BATTERY REPLACEMENT
When low battery indicator “ ” is displayed near the antenna icon
of the sensor(s), it indicates that the outdoor 7-IN-1 sensor and/or
current channel sensor(s) battery power is low respectively. Please
replace with new batteries.
8.2.1 RE-PAIRING THE SENSOR(S) MANUALLY
Whenever you changed the batteries of the 7-in-1 weather sensor array or other additional
sensors, re-synchronization must be done manually.
1. Change all the batteries to new ones in the low battery sensor(s).
2. Press
[ SENSOR / WI-FI ]
key on the console to enter sensor synchronization mode (as
indicated by the flashing antenna
).
8.3
RESET AND FACTORY RESET
To reset the console and start again, press the
[ RESET ]
key
once or remove the backup battery
and then unplug the adapter.
To resume factory settings and remove all data, press and hold the
[ RESET ]
key for 6 seconds.
29
8.1.1 FIRMWARE UPDATE STEP
1.
Download the latest version firmware to your PC/Mac.
2. Set the console into AP (access point) mode then connect the PC/Mac to the console (refer
to
section 6.1
and
6.2
).
3.
From the SETUP page, press ADVANCED to enter advance setting
4.
Under the firmware upload section, press
Browse
to locate the firmware file saved on
your PC/Mac.
5. Press
Upload
to start firmware update.
The update time is around 5 ~ 10 minutes. While updating, the
progress will be displayed (i.e. 100 is completion).
6. The console will restart once the update is completed.
7. The console will stay in
AP mode
for you to check the firmware version and all the current
setting. Simply press and hold
[ SENSOR / WI-FI ]
key for 6 seconds to exit AP mode.
IMPORTANT NOTE:
-
Please keep connecting the power during the firmware update process.
-Please make sure your PC/Mac's WI-FI connection is stable.
-
When the update process start, do not operate the PC/Mac and console until the update finished.
-
During firmware update the console will stop upload data to the cloud server. It will reconnect to your WI-FI
router and upload the data again once the firmware update succeed. If the console cannot connect to your
router, please enter the SETUP page to setup again.
-
After the firmware update, If the setup informations are missing, please input the setup information again.
-
Firmware update process have potential risk, which cannot guarantee 100% success. If the update fail,
please redo the above step to update again.
8.2
BATTERY REPLACEMENT
When low battery indicator “ ” is displayed near the antenna icon
of the sensor(s), it indicates that the outdoor 7-IN-1 sensor and/or
current channel sensor(s) battery power is low respectively. Please
replace with new batteries.
8.2.1 RE-PAIRING THE SENSOR(S) MANUALLY
Whenever you changed the batteries of the 7-in-1 weather sensor array or other additional
sensors, re-synchronization must be done manually.
1. Change all the batteries to new ones in the low battery sensor(s).
2. Press
[ SENSOR / WI-FI ]
key on the console to enter sensor synchronization mode (as
indicated by the flashing antenna
).
8.3
RESET AND FACTORY RESET
To reset the console and start again, press the
[ RESET ]
key
once or remove the backup battery
and then unplug the adapter.
To resume factory settings and remove all data, press and hold the
[ RESET ]
key for 6 seconds.
This display console supports OTA (over the air) Function Firmware and WI-FI System Firmware
updates via any web browser (not mobile browser) on a PC that is connected to Wi-Fi
®
. The update
function for both types of updates can be found at the bottom of the Advanced Tab on the wireless
settings interface (see Advanced Settings via Web Interface).
FIRMWARE UPDATE
28
6.4.1 CALIBRATION
1.
User can input the offset and/or gain values for different parameters while current offset and
gain values are shown next to their corresponding blank.
2. Once completed, press
Apply
at the bottom of the SETUP page.
The current offset value will show the previous value that you entered, please input the new
value in the blank if any changes needed, the new value will effective once you press
Apply
icon in SETUP page.
NOTE:
Calibration of most parameter is not required, with the exception of Relative Pressure, which
must be calibrated to sea-level to account for altitude effects.
7.
PROWEATHERLIVE (PWL) LIVE DATA & OPERATION
7.1
VIEW LIVE DATA
Login your ProWeatherLive account.
Once your device is connected, your device's live weather data will show on the dashboard
page.
NOTE:
Please press "Help" in the
should you have any query on the PWL operation.
8.
MAINTENANCE
8.1
FIRMWARE UPDATE
The console supports OTA firmware update capability. Its firmware may be updated over the air
anytime (whenever necessary) through any web-browser on a PC/Mac with WI-FI connectivity.
Update function, however, is not available through mobile/smart devices.
Upload
Browse
Firmware version: 1.00
Current firmware
version
Firmware update in ADVANCED page
Press to start upload the firmware
to console
Select the firmware file for update