www.logiquip.com
|
3
ASSEMBLY GUIDE
ASSEMBLY INSTRUCTIONS
MOUNT FIRST SHELF
(BOTTOM)
Refer to location of numbers on posts, snap tapered split sleeves on each post at the desired position for bottom shelf.
The thickest part of the tapered split sleeve goes to the bottom side of post. Be sure that the split sleeves have been
seated properly in the groove. Install bottom shelf first by sliding over the posts.
MOUNT ADDITIONAL SHELVES
Continue process for the next shelf by snapping split sleeves in the preferred location as before and sliding the shelf into
position. Follow the same procedure with each shelf working from the bottom up.
SECURE SHELVES
Place a board across the shelf corners and tap very lightly with a nylon or rubber base hammer to seat the shelf on the split
sleeves. CAUTION: Do not hammer directly on the wires or corner.
LEVELING OF UNIT
For wire racks with leveling feet place unit at desired location, and level using a bubble level. The leveling bolts, on post
bottom, allow 1/2” adjustments.
5 Shelf Wire Shelving Rack
Item# 5TB-12 / 5TZ-12
Assembly Instructions
Questions, Problems, Missing Parts?
Before returning to your retailer, CALL OUR CUSTOMER SERVICE DEPARTMENT at
1- 866-375-7994, 9 a.m. - 5 p.m. EST. MONDAY- FRIDAY. E-Mail: sales@shelfadditions.com
Tools Required For Assembly
Parts List
No tools required for assembly.
A (5) Shelf
C (4) Bottom Poles With Levelers Pre-installed
Helpful - Rubber Mallet
B (22) Plastic Tapered Lock Sets
D (4) Top Poles with Pole Connector & Caps Pre-installed
Note: White plastic discs used for packing only - Discard
SPECIAL WARNINGS
Assemble the item on a soft, non-abrasive surface, such as carpeting, to avoid scratching the finish.
Use care when handling. May require two adults for safe assembly.
CARE AND MAINTENANCE
Periodically check and make sure that all components are in their proper position, are free from damage and that all connectors are tight.
ASSEMBLY INSTRUCTIONS Estimated Assembly Time: Approximately 30 minutes
1. Post Assembly
Screw the two post sections together. Hands tighten. Note: the top
section has pole connector & cap. The bottom section has leveler.
2.
Bottom Shelf Assembly
a. Locate the desired position of the bottom shelf.
Note: Bottom shelf should be no more than six inches from the floor.
b. Insert four plastic tapered lock sets in the appropriate
pole groove, one in each pole. Ensure tapered end is up (see arrow on lock).
c. Place shelf on its side and slide each pole with tapered locks
through the bottom of the shelf until snug.
d. After all poles are in place, position the unit in the upright position.
e. Push down on each corner of the shelf, ensuring the shelf is in a
fully locked position.
3. Additional Shelf Assembly
a. Locate the desired position of the next lowest shelf and insert
the tapered locks into the poles.
b. Slide the shelf down from the top of the poles and onto the tapered locks.
Push down on each shelf corner, ensuring the shelf is in a fully locked position.
c. Repeat for the remaining shelves.
4. Leveler Adjustment
a. Move assembled unit to the selected room location.
b. If required, adjust levelers to ensure the unit is level.
Rotating the levelers counter clockwise raises the poles.
1-YEAR LIMITED WARRANTY
The manufacturer warrants this product to be free from defects in workmanship and material present at time of shipment from the factory for
one year from the date of purchase. This warranty applies only to the original purchaser. The manufacturer agrees to correct such defect at
no charge or at our option replace the product with a comparable or superior model.
To obtain warranty service, call our customer service department at 1-866-375-7994 for return authorization and shipping instructions. You
may be required to present a copy of your sales receipt as proof of purchase. All cost of removal and reinstallation are the expressed
responsibility of the purchaser. Any damage to the product by accident, misuse or improper installation, or by affixing accessories not
produced by the manufacturer, are the purchaser
’
s responsibility.
There is no further expressed warranty. The manufacturer disclaims any and all implied warranties. The manufacturer shall not be liable for
incidental, consequential or special damages arising at or in connection with product use or performance except as may otherwise be
accorded by law. This warranty gives you specific legal rights and you also have other rights that vary from state to state. This warranty
supersedes all prior warranties.
2/6/15 K
4 Shelf Heavy Duty Wire Shelving Rack
Vendor Stock# 4T601848C-LD
Assembly Instructions
Questions, Problems, Missing Parts?
Before returning to your retailer, CALL OUR CUSTOMER SERVICE DEPARTMENT at
1- 866-375-7994, 9 a.m. - 5 p.m. EST. MONDAY- FRIDAY. E-Mail:
sales@shelfadditions.com
Tools Required For Assembly
Parts List
No tools required for assembly.
A (4) Shelf C (4) Bottom Poles with Levelers Pre-installed
Helpful - Rubber Mallet B (32) Plastic Tapered Lock+4 extra D (4) Top Poles with Pole Connector & Caps
Pre-installed
Note: Black plastic discs used for packing only - Discard
SPECIAL WARNINGS
Assemble the item on a soft, non-abrasive surface, such as carpeting, to avoid scratching the finish.
Use care when handling. May require two adults for safe assembly.
CARE AND MAINTENANCE
Periodically check and make sure that all components are in their proper position, are free from damage and that all connectors are tight.
ASSEMBLY INSTRUCTIONS Estimated Assembly Time: Approximately 25 minutes
1. Post Assembly
Screw the two post sections together. Hands tighten. Note: the top
section has pole connector & cap. The bottom section has leveler.
2.
Bottom Shelf Assembly
a. Locate the desired position of the bottom shelf.
Note: Bottom shelf should be no more than six inches from the floor.
b. Insert four plastic tapered lock sets in the appropriate
pole groove, one in each pole. Ensure tapered end is up (see arrow on lock).
c. Place shelf on its side and slide each pole with tapered locks
through the bottom of the shelf until snug.
d. After all poles are in place, position the unit in the upright position.
e. Push down on each corner of the shelf, ensuring the shelf is in a
fully locked position.
3. Additional Shelf Assembly
a. Locate the desired position of the next lowest shelf and insert
the tapered locks into the poles.
b. Slide the shelf down from the top of the poles and onto the tapered locks.
Push down on each shelf corner, ensuring the shelf is in a fully locked position.
c. Repeat for the remaining shelves.
4. Leveler Adjustment
a. Move assembled unit to the selected room location.
b. If required, adjust levelers to ensure the unit is level.
Rotating the levelers counter clockwise raises the poles.
1-YEAR LIMITED WARRANTY
The manufacturer warrants this product to be free from defects in workmanship and material present at time of shipment from the factory for
one year from the date of purchase. This warranty applies only to the original purchaser. The manufacturer agrees to correct such defect at
no charge or at our option replace the product with a comparable or superior model.
To obtain warranty service, call our customer service department at 1-866-375-7994 for return authorization and shipping instructions. You
may be required to present a copy of your sales receipt as proof of purchase. All cost of removal and reinstallation are the expressed
responsibility of the purchaser. Any damage to the product by accident, misuse or improper installation, or by affixing accessories not
produced by the manufacturer, are the purchaser’s responsibility.
There is no further expressed warranty. The manufacturer disclaims any and all implied warranties. The manufacturer shall not be liable for
incidental, consequential or special damages arising at or in connection with product use or performance except as may otherwise be
accorded by law. This warranty gives you specific legal rights and you also have other rights that vary from state to state. This warranty
supersedes all prior warranties.
REV: 8/1/18
5 Shelf Wire Shelving Rack
Item# 5TB-12 / 5TZ-12
Assembly Instructions
Questions, Problems, Missing Parts?
Before returning to your retailer, CALL OUR CUSTOMER SERVICE DEPARTMENT at
1- 866-375-7994, 9 a.m. - 5 p.m. EST. MONDAY- FRIDAY. E-Mail: sales@shelfadditions.com
Tools Required For Assembly
Parts List
No tools required for assembly.
A (5) Shelf
C (4) Bottom Poles With Levelers Pre-installed
Helpful - Rubber Mallet
B (22) Plastic Tapered Lock Sets
D (4) Top Poles with Pole Connector & Caps Pre-installed
Note: White plastic discs used for packing only - Discard
SPECIAL WARNINGS
Assemble the item on a soft, non-abrasive surface, such as carpeting, to avoid scratching the finish.
Use care when handling. May require two adults for safe assembly.
CARE AND MAINTENANCE
Periodically check and make sure that all components are in their proper position, are free from damage and that all connectors are tight.
ASSEMBLY INSTRUCTIONS Estimated Assembly Time: Approximately 30 minutes
1. Post Assembly
Screw the two post sections together. Hands tighten. Note: the top
section has pole connector & cap. The bottom section has leveler.
2.
Bottom Shelf Assembly
a. Locate the desired position of the bottom shelf.
Note: Bottom shelf should be no more than six inches from the floor.
b. Insert four plastic tapered lock sets in the appropriate
pole groove, one in each pole. Ensure tapered end is up (see arrow on lock).
c. Place shelf on its side and slide each pole with tapered locks
through the bottom of the shelf until snug.
d. After all poles are in place, position the unit in the upright position.
e. Push down on each corner of the shelf, ensuring the shelf is in a
fully locked position.
3. Additional Shelf Assembly
a. Locate the desired position of the next lowest shelf and insert
the tapered locks into the poles.
b. Slide the shelf down from the top of the poles and onto the tapered locks.
Push down on each shelf corner, ensuring the shelf is in a fully locked position.
c. Repeat for the remaining shelves.
4. Leveler Adjustment
a. Move assembled unit to the selected room location.
b. If required, adjust levelers to ensure the unit is level.
Rotating the levelers counter clockwise raises the poles.
1-YEAR LIMITED WARRANTY
The manufacturer warrants this product to be free from defects in workmanship and material present at time of shipment from the factory for
one year from the date of purchase. This warranty applies only to the original purchaser. The manufacturer agrees to correct such defect at
no charge or at our option replace the product with a comparable or superior model.
To obtain warranty service, call our customer service department at 1-866-375-7994 for return authorization and shipping instructions. You
may be required to present a copy of your sales receipt as proof of purchase. All cost of removal and reinstallation are the expressed
responsibility of the purchaser. Any damage to the product by accident, misuse or improper installation, or by affixing accessories not
produced by the manufacturer, are the purchaser
’
s responsibility.
There is no further expressed warranty. The manufacturer disclaims any and all implied warranties. The manufacturer shall not be liable for
incidental, consequential or special damages arising at or in connection with product use or performance except as may otherwise be
accorded by law. This warranty gives you specific legal rights and you also have other rights that vary from state to state. This warranty
supersedes all prior warranties.
2/6/15 K
Snap plastic tapered split
sleeves on each post
Install shelf by sliding
over the posts
Tap very lightly with a nylon or
rubber base hammer to seat the
shelf on the split sleeves
