i)
Before starting work, hydraulic pipes and hoses shall be inspected and the stopping devices should be
tested.
j)
Selection and preparation of a suitable working are free from obstructions.
k)
The need to keep the working area free from obstructions, e.g. logs, split wood, etc.
l)
Check on the function of the machine: operate the unit without loading to check whether this unit works
normally (Refer to terms
3.
3.
3.
3. Operation
Operation
Operation
Operation
below). If the noises becoming louder and the ram running erratic
indicate there’s excessive air or a shortage of hydraulic oil in tank for you to release vent plug or add
hydraulic fluid.(Refer to Term 5. Maintenance and repair)
3.
3.
3.
3. Operation
Operation
Operation
Operation
NOTE:
a)
After log splitting, switch off and unplug the power cable.
b)
Ensure the horizontal distance between splitter and outlet is more than 3m in case of the dust influence.
c)
Allow only responsible adults who have read and understood the manual to operate this machine.
d)
Be familiar with all controls and proper operation. Know how to stop the machine quickly in the event of an
emergency.
e)
Don’t operate the machine while under the influence of alcohol, drugs or medication.
f)
Only a single operator is allowed to load and operate this log splitter. Keep bystanders, helpers, pets and
children a sufficient distance to the machine.
g)
Only use your hands to operate the control handles and the switch. Arms, feet, knees, rope, heavy objects
and extension device are not allowed.
h)
Never put any part of your body between the extending ram and the wedge.
i)
Don’t step over the splitter when the motor is running.
j)
Always split log along its grain. If across the grain, some types of wood may burst or fly out resulting in
injury.
k)
If you experienced problems splitting especially hard wood, don’t keep pushing on the handles. Release
both control handles at once, the ram will return. If keep pushing, the ram will fail to retract. If this occurs,
turn off the motor and on again to continue operation.
l)
If the log is clipped on the wedge, release both hands and unplug the power cable immediately. Knock off
the log with a hammer slightly (not with your hands).
m)
Never attempt to split more than one log at a time unless the ram has fully extended and a second log is
needed to complete the separation of the first log. Never attempt to split one log on top of another.
n)
Regularly clear the split wood to keep work area tidy for firm footing.
o)
Periodically check that all nuts, bolts, screws, hydraulic fittings and hose clamps are tightened.
p)
Never operate your splitter on wet, muddy or icy surface. Safe footing is essential in preventing accidents.
q)
Never leave the machine unattended with the motor running.
r)
Never use this machine in damp or rainy environment to avoid electric shock or short circuit.
s)
Operate log splitter in proper lighting.
t)
Never tamper with the motor to run it at excessive speeds. The maximum motor speed is preset by the
manufacturer and is within safety limits.
u)
Switch off and unplug power cable quickly when the machine is out of order. For example: the noises
becoming louder and the ram running erratic indicate there’s excessive air or a shortage of hydraulic oil in
tank for you to release vent bolt or add hydraulic fluid.(Refer to Term 5. Maintenance and repair)
v)
Don’t pull on power supply cable to unplug.
4.
4.
4.
4.
Transportation
Transportation
Transportation
Transportation
•
Put in the trunk of your car for a distant transportation.
•
Hold the towing handle to move about.
NOTE:
a)
Never move this machine while the motor is running.
b)
Be extra cautious when moving this machine on rugged and rough terrain.
c)
Be careful to keep upright, not to be tipped or crashed during transportation
d)
Never allow anyone to ride on the machine while moving.
8
8
8
8
•
Plug the power cable and switch on.
•
•••
Load log between log cradles and on the tank.
(Fig.
(Fig.
(Fig.
(Fig. 3)
3)
3)
3)
•
Move control handles down with both hands until the log
is split.
(Fig.
(Fig.
(Fig.
(Fig. 4)
4)
4)
4)
•
Release any hand to stop the ram extending.
•
Release both hands to retract the ram for
loading next log.
•
After log splitting, switch off and unplug the power cable.
Fig.
Fig.
Fig.
Fig. 3
3
3
3
Fig.
Fig.
Fig.
Fig. 4
4
4
4
