28
STACK CUTTING
Risk of serious injury if the warnings and
instructions in this manual are ignored!
Before you start cutting...
...you must have read and understood the warnings
and other instructions in this manual.
...The Stack Cutter must have been correctly set up
and stand secured in the right position as per the
sections “Preparations” and “Cut positioning”.
Lower the guide bar towards the stack. Select
a suitable guard length (A) for the guide bar tip
and set the guard to come as near as possible to
the stack. Winch the guide bar back up to its top
position.
The maximum permitted distance between the
stack and the guide bar guard is 50 mm. Longer
guide bar guards can be ordered from Logosol.
Check the guide bar’s path and the ground
beneath the guide bar, to ensure that you do not
saw through anything unintentionally.
Before cutting, check that the saw chain runs
freely and unobstructed on the electric saw. Wear
safety gloves.
Do not plug the power cable into the machine
until it is fixed in the right position.
Risk of the operator being hit by wood debris
thrown backwards in the direction of the chain.
Always stand with your face shielded by the
protective screen.
Refer to the section “The control panel”. Take a
firm grip of the winding crank before taking off the
safety catch.
During cutting, the saw unit must not be
pushed downwards to increase feed pressure. The
maximum feed pressure of the saw unit must be its
own weight. Take great care if the saw chain jams
because of “pinching”. If, at any time, the saw unit
does not descend easily through the stack, stop
cutting immediately. Disconnect the power and
remedy the fault. The cause may be that the saw
chain has jammed due to inwards pressure from
A
both sides (“pinching”) and, as a result, has lifted
from its groove on the top of the guide bar.
Extreme risk of chain breakage if the chain is
lifted out of the guide bar groove! Risk of fatal
injury! If the chain breaks, it may be thrown out at
high speed, either forwards or backwards, along the
axis of the guide bar.
Wind the saw slowly down to the stack and
continue all the way through the stack. Wind extra
slowly when trimming to avoid bar bending.
Stop the cutter by releasing the safety button or by
pushing the red stop button (see the section on the
control panel).
Summary of Contents for 0458-395-0603
