background image

To wake up Target Machine with Magic Packet

Step1: Target Machine:

Target Machine is necessary to use the WOL cable
link the Wake On LAN connector on adapter with
your motherboard. Check BIOS 

<POWER

MANGEMENT SETUP>

ACPI, Wake On LAN 

function must be enable. 

Step2: Target Machine:

Select

<Target Machine>

 then the system will setup

wakeup event and wait a magic packet to do system
wakeup

Step3: Master Machine:

Select

<Magic Packet>

 to send a magic packet and 

wake up the target machine. The MAC address of 
target machine will be asked for key-in, like 

           00 e0 7d c0 00 02. 
Step4: Target Machine:

ACPI Testing events will be show

Device State 1:     PASS
Device State 2:     PASS
Device State 3:     PASS

Step5: Target Machine:
           Put the Target Machine to power down mode.
Step6: Master Machine:
           Send a magic packet to wake up Target Machine.

Test the Wakeup Frame

Step1: Target Machine:

Select

<Target Machine>

 then the system will setup

wakeup event and wait a magic packet to do system
wakeup

Step2: Master Machine:
           Select

<WakeUp Frame>

 to send a wakeup frame.

Step3: Target Machine : 

ACPI Testing events will be show

Device State 1:     PASS
Device State 2:     PASS
Device State 3:     PASS

Note:

E-9

Adapter testing program can not be used in Windows
95/98 DOS mode. Do not load any device drivers, 
memory manager, and anti-virus software. The testing
program only can work in clean DOS prompt.

Summary of Contents for LCS-8038TXR7






























































Reviews: