Connecting the Cameras
Individual Power Adapter*
Multi-Camera Power Adapter*
Connecting the Cameras
* Images for representation only.
To install your camera:
1. Set the camera in the desired mounting position and mark
holes for screws through the camera base.
2. Drill the holes, then feed the cable through the mounting
surface or cable notch.
NOTE:
Insert the included drywall anchors if you are
mounting the camera onto drywall.
3. Mount the camera stand to the mounting surface using
the provided screws. Make sure all screws are fastened
tightly.
4. Adjust the camera as shown below:
Installing the Camera
Connect the male power head
and the BNC connector to the
camera.
Connect the BNC connector
to a video input on your DVR.
Connecting the Camera
Cable Notch
C841CA_QSG_EN_R1
Power Adapter Types
A multi-camera power adapter that provides power to multiple cameras
or individual power adapters may be provided, depending on product
configuration.
Problem
Solution
Picture does not
appear to be 4K
• To ensure that you are viewing camera video in full
4K resolution (4K monitor required), check the video
output resolution of your DVR. For full instructions,
see your DVR’s documentation at
lorex.com
.
No picture / signal
• The cameras are only compatible with certain Lorex
HD DVRs. For the full list of compatible recorders, visit
lorex.com/compatibility
.
• Ensure your TV or monitor is on the correct input
channel. Common terms for input channels: INPUT, AV
CHANNEL, LINE1, LINE2, AUX.
• Ensure your DVR is properly connected to your TV or
monitor.
• Ensure connections are properly connected.
• Ensure the camera power supply is plugged in.
Picture is too bright
• Ensure your camera isn’t pointed directly at a source
of light (e.g., sun or spot light).
• Check the brightness settings of the DVR and monitor.
• Move your camera to a different location.
Picture is too dark
• Check the brightness and contrast settings of the
DVR and monitor.
Night vision is not
working
• The night vision activates when light levels drop. The
area may have too much light.
Picture is not clear
• Check the camera lens for dirt, dust, spiderwebs.
Clean the lens with a soft, clean cloth.
• Make sure that the cable run is within the limitations
specified in the section ‘Cable Extension Options’.
• Remove the vinyl film from the camera lens when your
installation is complete.
Bright spot in video
when viewing camera
at night
• Night vision reflects when pointing a camera through a
window. Move the camera to a different location.
Person and vehicle
detection is not
working.
• Support for person and vehicle detection is
deteremined by your recorder. See your recorder’s
documentation to confirm support for this feature.
Troubleshooting
A. ROTATING THE ARM:
Loosen the adjustment ring by turning it
counter-clockwise. Rotate the arm of the camera up to 360°, then
tighten the adjustment ring against the base.
B. BENDING THE ARM:
Use a Phillips head screwdriver (not included)
to loosen the adjustment screw closest to the camera base. Bend the
arm of the camera up to 90°, then tighten the screw.
C. LEVELING THE CAMERA:
Use the screwdriver to loosen the
adjustment screw furthest from the camera base. Rotate the camera
until it is level with the viewing area, then tighten the screw.
ATTENTION:
Test your camera prior to selecting a permanent mounting location by
temporarily connecting the camera and cable to your DVR.
Before Installing the Camera
• Decide whether to run the cables
through the wall / ceiling (drilling
required) or along the wall / ceiling.
• If you run the cables along the
wall / ceiling, you must run the
cable through the
cable notch
on the
base. This will keep the camera base
flush to the surface when mounted.
A
B C
Connect the female power
head to the included power
adapter.
Camera
DVR
Male Power
Female Power
Setup Diagram
BNC Video
12V DC Power
Camera
Extension Cable
Power Adapter
HD DVR
Extend the cable run for your camera depending on the cable type used.
Additional extension cables sold separately. See table below:
Cable Extension Options
Option
Model Number
Cable Length
1
CB120URB
120ft (37m)
2
CB250URB
250ft (76m)
NOTES:
1. The extension cable must be a single stretch of cable between the DVR and
camera. You cannot connect multiple extension cables to each other.
2. Extending camera cable runs beyond the included cable length may require
you to connect the power supply directly to the camera rather than to the
extension cable.
3. Indicators that your cable run may be too long:
• Camera loses video when switching to night vision.
• Video is permanently black & white (even during day time).
• Video is unclear, soft, or distorted.
4. For more information on extension cables, visit
lorex.com
and search for the
model numbers of the cables above.
5. Remove the vinyl film from the camera lens when your
installation is complete.
