CAMÉRA DE VISION NOCTURNE DE SÉCURITÉ À L'ÉPREUVE DES INTEMPÉRIES
CÁMARA DE SEGURIDAD A PRUEBA DE AGUA, DE VISIÓN NOCTURNA
Entrada de video
DVR
BNC
Energía
Cámara
Energía
Adaptador de
energía
Version / Version / Versión 1.0
225mm / 8.9"
Male Power
BNC
1.
Connect the BNC and power
connectors to the camera.
Female Power
2.
Connect the BNC connector to the video
input of your DVR.
3.
Connect the power connectors to the
4-in-1 power adapter.
OR
Connect each camera to an individual
power adapter.
Connecting the Cameras
To DVR:
To Camera:
Image Sensor
1/3” 1.3 MP Sony Exmor® CMOS
Video Format
NTSC
Effective Pixels
H: 1305 V: 1049
Resolution
900 TVL
Scan System
2:1 Interlace
Sync System
Internal
S / N Ratio
48dB (AGC Off)
Iris
AES
AES Shutter Speed
1/60 ~ 1/100,000 sec.
Min. Illumination
0.01 Lux without IR LED; 0 Lux with IR LED
Video Output
Composite 1.0Vpp @ 75ohm
Lens / Lens Type
3.6mm F2.0 / Fixed
FOV (Diagonal)
92°
Termination
BNC Type
IR LED Qty. / Type
24 pieces / 850nm
Night Vision Range**
130ft (40m) / 90ft (28m)
Power Requirement
12V DC ±10%
Power Consumption
Max. 320mA (w / IR)
Operating Temp. Range
–4° ~ 122°F / –20° ~ 50°C
Operating Humidity Range
< 80% RH
Indoor/Outdoor***
Both (IP66)
Weight (including stand)
0.6lbs / 0.2kg
*
When connected to a 960H capable DVR.
*
* Stated IR illumination range is based on ideal conditions in typical outdoor night time ambient lighting and in
total darkness. Actual range and image clarity depends on installation location, viewing area, and light reflection /
absorption level of object.
*** Not intended for submersion in water. Installation in a sheltered location recommended.
Before installing the cameras:
• Decide whether to run the cables
through
the wall / ceiling
(drilling required) or
along
the wall / ceiling.
• If you run the cables along the wall / ceiling, you must run the
cable through the cable notch on the base. This will keep the
camera base flush to the surface when mounted.
To install the cameras:
1. Set the camera in the desired mounting position and mark holes for
screws through the camera base.
2. Drill the holes, then feed the cable through the
mounting surface or cable notch and mount
the camera stand to the surface using the
provided screws. Make sure all screws are
fastened tightly.
3. Set the position and angle of the camera.
Installing the Cameras
ATTENTION
- Test each camera prior to selecting a permanent mounting location by
temporarily connecting the camera(s) and cables to the DVR.
B) Loosen lower screw with the
Allen key to adjust the camera’s
vertical position.
C) Loosen upper screw with the
Allen key to rotate the camera
housing.
A) Turn the adjustment ring
to tighten / loosen the stand
connection. Adjust the camera’s
horizontal position.
4. Remove the protective film from the camera lens.
A
B
C
Camera Specifications
Cable Notch
Installation Tips
• Point the cameras where there is the least amount of obstructions (i.e.
tree branches).
• Install the cameras where they are difficult for vandals to reach.
• Secure cabling so that it is not exposed or easily cut.
• Cameras rated for outdoor use. Installation in a sheltered location
recommended.
Contents
• IR Night Vision Camera*
• Mounting Kit / Allen Key*
• 60ft BNC / Power Extension Cable*
• Power Adapter**
WARNING
- A REGULATED UL / CSA APPROVED power supply is REQUIRED for use
with this camera. Use of a non-regulated, non-conforming power supply can damage this
product and voids the warranty.
*Model CVC7721PK4 is a 4-pack that includes four of the listed items.
** A “4-in-1” Power Adapter that provides power to four cameras or individual power adapters
may be provided, depending on product configuration.
Warning/Caution
• Read this guide carefully and keep it for future reference.
• Follow all instructions for safe use of the product and handle with
care.
• Use the cameras within given temperature, humidity and voltage levels
noted in ‘Camera Specifications’.
• Do not disassemble the cameras.
• Do not point the cameras directly towards the sun or a source of
intense light.
• Use only the supplied regulated power supply. Use of a non-regulated,
non-conforming power supply can damage this product and voids the
warranty.
• Periodic cleaning may be required. Use a damp cloth only. Do not use
harsh cleaners or aerosol cleaners.
• The supplied extension cable is rated for surface mounting only.
• Cables for in-wall / floor-to-floor installations are sold separately.
ATTENTION
- This camera includes an Auto Mechanical IR Cut Filter. When the camera
changes between Day/Night viewing modes, an audible clicking noise may be heard
from the camera. This clicking is normal, and indicates that the camera filter is working.
ENGLISH
Video Input
DVR
Extension Cable
BNC
Power
Camera
Power
Entrée vidéo
DVR
BNC
Alimentation
Caméra
Alimentation
Adaptateur
d’ alimentation
Rallonge
Power Adapter
Cable de
extensión
WEATHERPROOF NIGHT VISION SECURITY CAMERA
Quick Start Guide
Guide de démarrage rapide
Guía de inicio rápido
CVC7721 SERIES / SÉRIE / SERIE
67mm /
2.6"
Dimensions / Dimensions / Dimensiones
73mm / 2.9"
Copyright © 2014 Lorex Corporation
Ya que nuestros productos están sujetos a mejoras continuas, Lorex se reserva el derecho de modificar el diseño
de la imagen, las especificaciones y los precios sin aviso y sin incurrir en ninguna obligación. E&OE
Copyright © 2014 Lorex Corporation
Nos produits étant sans cesse améliorés, Lorex se réserve le droit de modifier la conception du produit, les
spécifications et les prix sans préavis et sans aucune obligation. E&OE
www.lorextechnology.com
Copyright © 2014 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves the right to modify product design,
specifications and prices, without notice and without incurring any obligation. E&OE
Setup Diagram
Schéma d’interconnexion
Diagrama de configuración
