Connecting the Cameras
Individual Power Adapter*
Multi-Camera Power Adapter*
Connecting the Cameras
* Images for representation only
To install your camera:
1. Set the camera in the desired mounting position and mark
holes for screws through the camera base.
2. Drill the holes, then feed the cable through the mounting
surface or cable notch.
Installing the Camera
Extend the cable run for your camera depending on the cable type used.
Additional extension cables sold separately. See table below:
Connect the male power head
and the BNC connector to the
camera.
Connect the BNC connector
to a video input on your DVR.
Connecting the Camera
Cable Notch
LBV4711_QSG_EN_R2
Power Adapter Types
A multi-camera power adapter that provides power to multiple cameras
or individual power adapters may be provided, depending on product
configuration.
Problem
Solution
No picture / signal
• The cameras are only compatible with certain
Lorex HD DVRs. For the full list of compatible
recorders, visit
lorex.com/compatibility
• Ensure your TV or monitor is on the correct
input channel. Common terms for input
channels: INPUT, AV CHANNEL, LINE1, LINE2,
AUX.
• Ensure your DVR is properly connected to
your TV or monitor.
• Ensure connections are properly connected.
• Ensure the camera power supply is plugged
in.
Picture is too bright
• Ensure your camera isn’t pointed directly at a
source of light (e.g., sun or spot light).
• Check the brightness settings of the DVR
and monitor.
• Move your camera to a different location.
Picture is too dark
• Check the brightness and contrast settings
of the DVR and monitor.
Night vision is not
working
• The night vision activates when light levels
drop. The area may have too much light.
Picture is not clear
• Check the camera lens for dirt, dust,
spiderwebs. Clean the lens with a soft, clean
cloth.
• Make sure that the cable run is within the
limitations specified in the section ‘Cable
Extension Options’.
• Remove the vinyl film from the camera lens
when your installation is complete.
Bright spot in video when
viewing camera at night
• Night vision reflects when pointing a camera
through a window. Move the camera to a
different location.
Troubleshooting
A. ROTATING THE ARM:
Rotate the camera stand up to 360°.
B. BENDING THE ARM:
Bend the arm of the camera up to 90°.
C. LEVELING THE CAMERA:
Rotate the camera until it is level with
the viewing area, then tighten the adjustment screw.
ATTENTION:
Test your camera prior to selecting a permanent mounting location by
temporarily connecting the camera and cable to your DVR.
Before Installing the Camera
• Decide whether to run the cables
through the wall / ceiling (drilling
required) or along the wall / ceiling.
• If you run the cables along the
wall / ceiling, you must run the
cable through the
cable notch
on the
base. This will keep the camera base
flush to the surface when mounted.
Connect the female power
head to the included power
adapter.
Camera
DVR
Male Power
Female Power
Setup Diagram
BNC Video
12V DC Power
Camera
Extension Cable
Power Adapter
HD DVR
Cable Extension Options
Option
Cable Type
Max Cable Run
Distance
1
Lorex model MCBL-60BNC4 BNC Cable
(included with camera)
60ft (18m)
2
‘RG59’ or ‘Coax’ or ‘Coaxial BNC’ Siamese
(Video and Power)
300ft (91m)
3
‘RG59’ or ‘Coax’ or ‘Coaxial BNC’ (Video
Only)
2
1000ft (305m)
NOTES:
1. The extension cable must be a single stretch of cable between the
DVR and camera. You cannot connect multiple extension cables to
each other.
2. For cable runs above
300ft (91m), you must connect the power
adapter directly to the camera, rather than at the end of the
extension cable.
3. If using a balun, ensure it is rated for the maximum supported
resolution of the camera (e.g., a 4MP camera requires a balun rated
for 4MP or above).
4. Indicators that your cable run may be too long:
• Video is permanently black & white (even during day time).
• Video is unclear, soft, or distorted.
5. For more information on extension cables, visit
lorex.com
.
4. Use a Philips head screwdriver (not included) to loosen the
adjustment screw.
5. Adjust the postion of the camera as needed:
A
Adjustment Screw
3. Mount the camera stand
to the surface using the
provided screws. Make
sure all screws
are fastened tightly.
NOTE:
Insert the
included drywall anchors
if you are mounting the
camera onto drywall.
6. Tighten the adjustment screw when finished.
7. Remove the vinyl film from the camera lens when your
installation is complete.
Drywall anchors (×3)
Mounting surface
Mounting screws (×3)
Camera
base
B
C
