HD Wi-Fi Active Deterrence Camera
Quick Start Guide
www.lorex.com
Package Contents
HD Wi-Fi
Camera
ATTENTION:
A REGULATED UL / CSA APPROVED power supply is REQUIRED for use
with this camera (included). Use of a non-regulated, non-conforming
power supply can damage this product and voids the warranty.
Camera Overview
Lens
Motion (PIR) Sensor
Microphone
Spotlights / Indicator LED
Speaker
Reset Button:
Press and hold to reset
the camera. The indicator LED will
quickly flash red, then green, then
yellow when the camera is reset.
microSD Slot:
microSD card pre-
inserted (expandable up to 128GB).
A
B
C
D
E
A
B
C
D
E
F
F G
G
Mounting
Stands
USB Power
Adapter
Mounting Kit
Safety Precautions
• Read this guide carefully and keep it for future reference.
• Follow all instructions for safe use and handling of the product.
• Use the camera within given temperature, humidity and voltage levels
noted in the camera’s specifications.
• Do not disassemble the camera.
• Do not point the camera directly at the sun or a source of intense light.
• Periodic cleaning may be required. Use a damp cloth only. Do not use
any harsh, chemical-based cleaners.
Visit us online for up-to-date software and
complete instruction manuals.
Click on the
Downloads
tab
4
Visit
lorex.com
Search for the model number
of your product
Click on your product in the
search results
3
2
1
Copyright © 2019 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves the right
to modify product design, specifications and prices, without notice and without
incurring any obligation. E&OE. All rights reserved.
• Place the camera as close to your Wi-Fi router or access point as possible.
• Reduce the number of obstructive materials between the camera and
the router or access point. Concrete, brick, metal and wood are the most
common materials in your house that can cause poor signal strength.
To ensure the best possible wireless performance, it is
recommended to keep the following installation tips in mind when
choosing a location for the camera:
•
The camera uses the 2.4GHz band exclusively.
Most new routers support
both 2.4GHz and 5GHz bands. It is recommended to use other Wi-Fi
devices on the 5GHz band when possible to ensure the 2.4GHz band is not
overcrowded.
• Other electronic devices such as microwaves, TVs, cordless phones, and
baby monitors can cause signal interference. It is recommended to install
the camera as far away from these devices as possible.
• Point the camera where there is the least amount of obstructions (i.e.,
tree branches).
• Install the camera where vandals cannot easily reach.
• This camera is rated for outdoor use. Installation in a sheltered location
is recommended.
Additional Positioning Tips
LNWCM22Y_QSG_EN_R1
Installation Tips
Troubleshooting
Problem
Solution
Cannot set up
camera
• Ensure you are using a
2.4GHz Wi-Fi network
to
configure the camera.
The camera does not work
with 5GHz networks.
• Ensure your mobile device is within 1ft (30cm) of
the camera during setup.
No picture /
signal
• Ensure the LED indicator on the camera is
glowing steady green. See ‘LED Behavior’ section
for details if otherwise.
• Ensure the camera is properly connected to
power using the included USB power adapter.
• Try repositioning the camera, router, or both to
improve signal strength.
Picture is not
clear
• Check the camera lens for dirt, dust, spiderwebs.
Clean the lens with a soft, clean cloth.
• Remove the vinyl cover on the camera lens.
No audio
• Ensure audio function on camera is turned on.
• Ensure audio is turned up on viewing device.
The warning
light is not
switching on
automatically
• Ensure that you have enabled and configured
white light deterrence.
The siren is not
switching on
automatically
• The camera siren cannot switch on automatically.
You can control the camera siren manually using
the Lorex Home app.
×9
×9
×4
×1
LED Behavior
See table below for definitions of camera’s LED behaviors:
Behavior
Meaning
(steady)
Operating correctly.
(flashing)
Connecting to network.
(steady)
Device malfunction. Try resetting the camera
(see ‘Camera Overview’ for details) and
repeating the setup.
(flashing)
Network connection failed. Try resetting the
camera (see ‘Camera Overview’ for details)
and repeating the setup.
(flashing rapidly)
microSD error. Try removing and re-inserting
the included microSD card, or try a different
card.
Camera was successfully reset. Wait until the
LED glows green before connecting to the
camera.
Need Help?
Disclaimers
• Not intended for submersion in water. Installation in a sheltered location
recommended.
• This camera includes an Auto Mechanical IR Cut Filter. When the camera
changes between Day/Night viewing modes, an audible clicking noise may
be heard from the camera. This clicking is normal, and indicates that the
camera filter is working.
• Audio recording without consent is illegal in certain jurisdictions. Lorex
Corporation assumes no liability for use of its products that does not
conform with local laws.
3
2
1
*
* Use the included access tool to remove the
service compartment cover.
Access
Tool
LNWCM22Y Series
