Lorex Technologies Inc.
Copyright © 2011 Lorex Technologies Inc.
As our products are subject to continuous improvement, Lorex reserves the right to modify product design,
specifications and prices, without notice and without incurring any obligation. E&OE
Cable Extension Options
Problem
Solution
No Picture/Signal
•
Ensure your TV is on the correct input channel.
Common terms of an input channel: INPUT,
AV CHANNEL, LINE1, LINE2, AUX.
•
If your camera is connected to a VCR/DVR,
ensure it is properly connected to your TV/
Monitor.
•
Ensure connections are properly connected.
•
Ensure the camera power supply is plugged
in.
Picture is too bright
•
Ensure your camera isn’t pointed directly at a
source of light (e.g sun or spot light).
•
Slide the sunshade (bullet cameras only)
forward to block excess light.
•
Move your camera to a different location.
Picture is too dark
•
If using during the day, the camera may not
be getting enough light. Slide the sunshade
backwards to let in more light. Check the
brightness and contrast settings of the device
your camera connects to (TV/Monitor/DVR).
Night Vision is not
working
•
The night vision activates when light levels
drop. The area may have too much light.
Picture is not clear
•
Check the camera lens for dirt, dust,
spiderwebs. Clean the lens with a soft, clean
cloth.
•
Make sure that the cable run is within the
limitations specified in the section ' Cable
Extension Options'
Bright spot in video
when viewing camera
at night
•
Night vision reflects when pointing a camera
to a window. Move the camera to a different
location.
BNC connection does
not connect to my TV
•
Use a BNC to RCA adapter at the end of the
extension cable.
Troubleshooting
Option
Cable Type
1
Regular BNC (sup-
plied with cam-
era)
180ft / 55m
3
2
'RG59' or 'Coax'
or ' Coaxial' BNC
(sold separately)
300ft / 92m
5
3
Lorex Universal
Cable
(sold separately)
300ft / 92m
3
Max. Cable
Run Distance
Notes:
1.
For optimal performance, consider using option 2 or 3. Preference for using
the same cable type for the entire distance.
2.
Cable run recommendation based on typical camera power consumption
(up to 500mA). For specialty cameras with higher current consumption,
maximum cable run may be reduced. Consider providing power to the
camera at the camera side rather then at the end of the extension cable.
3.
Indicators that your cable run may be too long:
•
Video is permanently Black & White (even during day time)
•
Video is distorted
Max. # of
Extensions
Image Sensor
1/3" Sony Super HAD™ II
Video Format / Pixels
Horizontal Resolution
Video Output
IR / Night Vision Range
Field of View (diagonal)
Minimum Illumination
Termination
NTSC: 768(H)×494(V)
600 TVL
Comp. 1.0 Vpp @ 75ohm
60 Degrees
0 LUX (IR LEDs on)
Video: BNC Female
Power: Barrel Female
Lens / Lens Mount
6.0mm F2.0 / Fixed
Camera Specifications
Product Information
User Manuals
Quick Start Guides
Specification Sheets
Software Upgrades
Firmware Upgrades
www.lorextechnology.com
IT’S ALL ON THE WEB!
Extend the cable run for your camera up to 300ft or more
depending on the cable type used. See table below:
Operating Temperature
14°F ~ 122°F
(-10°C ~ 50°C)
Power Requirement
12V DC ±10%
Power Consumption
600 mA or 7.2W max
Weight (with stand)
1.6lbs. / 0.8 kg
47 IR LED/120 ft. (37 m)*
Environmental Rating
IP 66*
4 in / 101mm
10.5 in/ 267mm
4 in /
101mm
*Not intended for submersion in water. Installation in a sheltered location recommended.
**IR Illumination range under ideal conditions. Objects at or beyond this range may be
partially or completely obscured, depending on the camera application.
SUPER RESOLUTION
IR NIGHT VISION CAMERA
LBC6050 Series
English Version
2
.0
QUICK START GUIDE
