background image

 

 

 

Sound Advice 

 

Kindling after some lengthy pause 

If the insert has not been used for a protracted period, it should be checked 

whether the smoke ducts are intact, and whether there might be blockings in the 

chimney prior to kindling. 

 

Chimney Fire 

In the event of chimney fire, it is recommended to close the door and the 

damper, and possibly call the fire brigade. 

 

Cleaning of Fireplace Insert 

All Lotus fireplace inserts have been factory surface treated using original 

Senotherm lacquer in colours ”coke” or ”grey”. This treatment will make the 

fireplace insert exude a special smell during the initial kindlings but this will 

vanish after a few times. Provide good airing. Maintain the surface by brushing 

it, using a soft, long-haired auto brush. A cloth with water or other matter may 

not be used. 

 

Maintenance of Fireplace Insert 

It is recommended that the maintenance of your stove be performed by a 

qualified service engineer, and that only spares recommended by the 

manufacturer be used. 

 

Packings

 may look neat but they will collapse in the heat and will thus lose 

their ability to keep the fireplace insert tight. Packings should be replaced as 

required since good combustion and a clean pane will very much depend on the 

fireplace insert being tight. 

 

Skamol broken or Worn may easily be replaced as these have been mounted 

loosely, the plates are made of vermiculite this is an insulating material, and the 

material is lighter porous. 

To avoid breaking the plates, it is important that

 

wood is not thrown, but rather added into the middle of the firebox

. Should 

you get to crack a skamolplate, it has no significance for insulation. 

 

 

The smoke turn plate

 may be worn. It is readily replaced and is fitted as 

described above. 

Summary of Contents for H470W




















Reviews: