background image

 

  Safety Notes

 

Before operating this aircraft, please read the user manual.    Reading the user manual will 

ensure proper, safe operation of the aircraft. 

1. 

This radio controlled aircraft is intended to be operated by pilots with prior flight 

experience.    We advise that all new pilots be at least 15 years of age and receive 

proper training prior to attempting to operate the aircraft.

   

2. 

This aircraft makes use of high speed, rotating propellers to fly.    To avoid personal 

injury, please do not attempt to stop the propellers with any part of the body

.   

3. 

The radio control aircraft and the ground control software have been thoroughly 

tested prior to shipment and therefore a pilot should NOT try to modify or change the 

settings unless following instruction in this manual

4.  The ground control software maintains a log file on the PC it is installed on.    Please ensure 

the safe keeping of these log files as they may be needed for warranty issues.   

5.  If you notice any irregularities during autonomous flight or experience and emergency, 

IMMEDIATELY switch to manual flight control to avoid any damage to the aircraft or the 

surroundings in which you are flying. 

6.  Please land the model immediately when the signal lights turned (turn) white. 

7.  Ensure that you have proper GPS connection prior to executing any GPS related functions. 

GPS lock will be indicated by a flashing red light on the aircraft. 

8.  While aircraft is airborne, DO NOT execute any commands intended to be used while aircraft 

is not airborne.   

9.  Once the AUTO LAND command is executed, it cannot be canceled.   

 

  DISCLAIMER

 

1.

 

Do not use this product for anything other than the intended applications.   

 

2.

 

It is the operator’s/pilot’s responsibility to know the laws and regulations 
pertaining to the operation of this aircraft in their area of intended operation.   
The operator/pilot bears all responsibility for the use of the aircraft.

 

3.

 

This aircraft contains a large number of sophisticated electronic components that 
may fail over time.    LotusRC and our dealers assume no responsibility for any 
damage caused by such a failure, be it direct or indirect.

 

.   

Upon purchase of this product, the purchaser agrees to the above conditions.     

Summary of Contents for T600G





















Reviews: