I271
I
GB
F
E
02
17
31100324
I
30
M08 - SOGLIE LIMITE UdM Default Range
P08.n.01 Misura di riferimento OFF OFF- (misure)
P08.n.02 Funzione Max Max - Min - Min+Max
P08.n.03 Soglia superiore 0 -9999 - +9999
P08.n.04 Moltiplicatore x1 /100 - x10k
P08.n.05 Ritardo sec 0 0.0 - 600.0
P08.n.06 Soglia inferiore 0 -9999 - +9999
P08.n.07 Moltiplicatore x1 /100 - x10k
P08.n.08 Ritardo sec 0 0.0 - 600.0
P08.n.09 Stato a riposo OFF OFF-ON
P08.n.10 Memoria OFF OFF-ON
Nota:
questo menu è diviso in 8 sezioni, per le soglie limite LIM1..8
P08.n.01
– Definisce a quale delle misure del multimetro applicare la soglia limite.
P08.n.02
– Definisce il funzionamento della soglia limite. Può essere:
Max
= LIMn attivo quando la misura supera P08.n.03. P08.n.06 è la soglia di ripristino.
Min
= LIMn attivo quando la misura è inferiore a P08.n.06. P08.n.03 è la soglia di ripristino.
Min+Max
= LIMn attivo quando la misura è superiore a P08.n.03 oppure inferiore a P08.n.06.
P08.n.03 e P08.n.04
– Definiscono la soglia superiore, che è data dal valore di P08.n.03 moltiplicato per P08.n.04.
P08.n.05
– Ritardo di intervento sulla soglia superiore.
P08.n.06, P08.n.07, P08.n.08
– come sopra, riferiti alla soglia inferiore.
P08.n.09
– Permette di invertire lo stato del limite LIMn.
P08.n.10
– Definisce se la soglia rimane memorizzata e va azzerata manualmente (ON) o se si ripristina automaticamente (OFF).
M09 - ALLARMI Default Range
P09.n.01 Sorgente allarme OFF OFF-LIMx-INPx-BOOx
P09.n.02 Numero canale (x) 1 1-8
P09.n.03 Memoria OFF OFF-ON
P09.n.04 Priorità Low Bassa - Alta
P09.n.05 Testo ALAn (testo - 16 char)
Nota:
questo menu è diviso in 8 sezioni, per gli allarmi ALA1..8
P09.n.01
– Segnale che provoca l’allarme. Può essere il superamento di una soglia (LIMx), l’attivazione di un ingresso esterno (INPx), una condizione logica Booleana (BOOx).
P09.n.02
– Numero del canale x riferito al parametro precedente.
P09.n.03
– Definisce se l’ allarme rimane memorizzato e va azzerato manualmente (ON) o se si ripristina automaticamente (OFF).
P09.n.04
– Se l’allarme ha priorità alta, al suo verificarsi provoca lo spostamento automatico del display sulla pagina allarmi e viene visualizzato con l’icona di attenzione. Se invece è impostato su priorità bassa, la
pagina non cambia e viene visualizzato con l’icona di informazione.
P09.n.05
– Testo libero dell’allarme. Max. 16 caratteri.
M07 - COMUNICAZIONE UdM Default Range
P07.n.01 Indirizzo seriale nodo 01 01-255
P07.n.02 Velocità seriale bps 9600 1200
2400
4800
9600
19200
38400
57600
115200
P07.n.03 Formato dati 8 bit - n 8 bit, no parity
8bit, odd
8 bit, even
7 bit, odd
7 bit, even
P07.n.04 Bit di stop 1 1-2
P07.n.05 Protocollo Modbus RTU Modbus RTU
Modbus ASCII
Modbus TCP
P07.n.06 Indirizzo IP 000.000.000.000 000.000.000.000 -
255.255.255.255
P07.n.07 Subnet mask 000.000.000.000 000.000.000.000 -
255.255.255.255
P07.n.08 Porta IP 1001 0-9999
P07.n.09 Funzione Gateway OFF OFF/ON
P07.n.10 Client / server Server Client / Server
P07.n.11 Indirizzo IP remoto 000.000.000.000 000.000.000.000 –
255.255.255.255
P07.n.12 Porta IP remota 1001 0-9999
P07.n.13 Indirizzo gateway IP 000.000.000.000 000.000.000.000 –
255.255.255.255
Nota:
questo menu è diviso in 2 sezioni, per i canali di comunicazione COM1..2
P07.n.01
– Indirizzo seriale (nodo) del protocollo di comunicazione.
P07.n.02
– Velocità di trasmissione della porta di comunicazione.
P07.n.03
– Formato dati. Impostazioni a 7 bit possibili solo per protocollo ASCII.
P07.n.04
– Numero bit di stop.
P07.n.05
– Scelta del protocollo di comunicazione.
P07.n.06, P07.n.07, P07.n.08, P07.n.13
– Coordinate TCP-IP per applicazioni con interfaccia Ethernet. Non utilizzati con altri tipi di moduli di comunicazione.
P07.n.09
– Funzione non supportata.
P07.n.10
– Attivazione della connessione TCP-IP.
Server
= Attende connessione da un client remoto.
Client
= Stabilisce connessione verso un server remoto.
P07.n.11, P07.n.12
– Coordinate per la connessione al server remoto quando P07.n.10 è impostato a client.