background image

Lowell UPS8 Series Manual

Pg. 27

LIMITED WARRANTY

Lowell Manufacturing Company warrants Lowell UPS equipment, when properly applied and operated within specified 
conditions, against faulty materials or workmanship for a period of 

three years for UPS8 Series products

 from the date 

of purchase . Lowell Manufacturing Company warrants 

internal batteries for a period of three years 

from the date of 

purchase . For equipment sites within the United States and Canada, this warranty covers repair or replacement, at the sole 
discretion of Lowell Manufacturing Company . The customer is responsible for the costs of shipping the defective product to 
Lowell Manufacturing Company . Lowell Manufacturing Company will pay for ground shipment of the repaired or replacement 
product . This warranty applies only to the original purchaser .

If equipment provided by Lowell Manufacturing Company is found to be 

Dead-on-Arrival (DOA)

, Lowell Manufacturing 

Company will be responsible for the costs of shipping product to and returning equipment from the customer in a timely 
manner as agreed to with the customer, once the customer has requested and received a 

Return Material Authorization 

(RMA) 

number . DOA equipment is defined as equipment that does not properly function according to user documentation 

when initially received and connected in conjunction with proper procedures as shown in the user documentation or via 
support provided by Lowell Manufacturing Company personnel or authorized agents .

This warranty shall be void if (a) the equipment is repaired or modified by anyone other than Lowell Manufacturing Company 
or a Lowell Manufacturing Company approved third party; (b) the equipment is damaged by the customer, is improperly used 
or stored, is subjected to an adverse operating environment, or is operated outside the limits of its electrical specifications; or 
(c) the equipment has been used or stored in a manner contrary to the equipment’s operating manual, intended use or other 
written instructions . Any technical advice furnished by Lowell Manufacturing Company or a Lowell Manufacturing Company 
authorized representative before or after delivery with regard to the use or application of Lowell Manufacturing Company 
equipment is furnished on the basis that it represents Lowell Manufacturing Company’s best judgment under the situation and 
circumstances, but it is used at the recipient’s sole risk .

EXCEPT AS STATED ABOVE, Lowell Manufacturing Company DISCLAIMS ALL WARRANTIES, EXPRESSED OR IMPLIED, 
INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE .

EXCEPT AS STATED ABOVE, IN NO EVENT WILL Lowell Manufacturing Company BE LIABLE FOR DIRECT, INDIRECT, 
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF Lowell Manufacturing Company 
UPS8 Series EQUIPMENT, including but not limited to, any costs, lost profits or revenue, loss of equipment, loss of use 
of equipment, loss of software, loss of data, cost of substitutes, or claims by third parties . Purchaser’s sole and exclusive 
remedy for breach of any warranty, expressed or implied, concerning Lowell Manufacturing Company equipment, and the only 
obligation of Lowell Manufacturing Company under this warranty, shall be the repair or replacement of defective equipment, 
components, or parts; or, at Lowell Manufacturing Company’s sole discretion, refund of the purchase price or substitution of 
an equivalent replacement product . 

Summary of Contents for UPS8-1100





































Reviews: