Chapter 7. Usage of Various Functions
7-48
Conversion method is as below.
Scaling conversion value (A/D conversion =
3200
4000]
800]
20mA)
~
0
of
[(data
×
−
Example) 8mA input in the range of 0 ~ 20
㎃
- Before the scaling conversion : 8
㎃
/ 5
㎂
= 1600
- After the scaling conversion: (1600 –800) x 1.25 = 1000
Scaling conversion value (D/A conversion) =
800
4000
3200]
20mA)
~
0
of
[(data
+
×
Example) Output 1000 in the range of 0 ~ 20
㎃
- Current output value before the scaling conversion : 1000 x 5
㎂
= 5
㎃
- Current output value after the scaling conversion: (1000 x 0.8) + 800 = 1600
1600 x 5
㎂
= 8
㎃
4) Wiring
(1) Caution for wiring
•
Make sure that external input signal of the mixture module of AC and analog I/O is not affected by induction noise or
occurs from the AC through using another cable.
•
Wire is adopted with consideration about peripheral temperature and electric current allowance. For wire, thicker than
AWG22 (0.3
㎟
) one is recommended.
•
If wire is put near to high temperature radiated device or contacted with oil for a long time, it may cause of electric
leakage so that it gets broken or miss-operation during wiring.
•
Be sure to connect with care of polarity while connecting to external 24V DC power supply.
•
In case of wiring with high voltage line or generation line, it makes induction failure so then it may cause of miss-
operation and out of order.
(2) Wiring example
a) Analog input
Input
+
-
+
-
Input
Voltage input
Current input
V0
I0
COM0
V1
I1
COM1
Terminal
*1
*1
Terminal
Summary of Contents for GLOFA G7M-DR20U
