background image

3 - 38

If the engine stops, the operation of steering wheel becomes hard to turn and 

causes steering not to work. But this does not mean a failure.

If you turn the steering wheel while driving, the steering wheel does not return back 

automatically. 

Notice

(2) Steering system

The hydraulic steering system controlled by fluid power provides you more convenience to operate 

the steering wheel.

Notices when using the steering system.

1. If there is too much of a load in front loader bucket, it could be difficult to operate the steering wheel. 

In this case, reduce the size of the load.

2. After turning the steering wheel fully, do not turn the steering wheel to the same direction again. As 

the unnecessary force is applied, this could damage to the steering system. Especially, DO NOT 
operate the steering wheel by force if the front wheel mired in the ditch. In this case, the rim could be 
affected and damaged.

3. If it sounds abnormal when operating the steering wheel, this means that there is some air in the 

steering components and line. In this case, turn the steering wheel to the left and right fully and hold 
it for about 5 seconds, and the air shall bleed out and the abnormal noise shall disappear. If it’s not 
cleared, contact your authorized local dealer for repair.

4. When starting engine in cold weather, a abnormal noise may occur. In this case, warm up the tractor 

before using to reduce the oil viscosity.

5. If you use the tractor for a long time while turning the steering wheel fully, the oil temperature will 

increase which may cause the reduction of the product life or the failure of hydraulic and steering 
system.

Summary of Contents for MT5 Series

































































































































































































Reviews: