Learning Advanced Features
186
Code
Description
EPI-13EPID1 Out
LPF
Used when the output of the EPID controller changes too fast or the
entire system is unstable, due to severe oscillation. In general, a lower
value (default value=0) is used to speed up response time, but in
some cases a higher value increases stability. The higher the value,
the more stable the EPID controller output is, but the slower the
response time.
EPI-14 EPID1 Limit
Hi,
EPI-15 EPID1 Limit
Lo
Limits the output of the controller.
EPI-16
EPID1 Out Inv
If EPID Out Inv is
set to ‗Yes,‘ the difference (error) value between the
reference and the feedback is set as the feedback
–reference value.
EPI-17 EPID1 Unit
Sel
Sets the unit for the control variable.
0: CUST is a custom unit defined by the user.
Setting
0
CUST
21
m 3/m(m 3/min)
1
%
22
m 3/h(m 3/h)
2
PSI
23
l/s
3
˚F
24
l/m
4
˚C
25
l/h
5
inWC
26
kg/s
6
inM
27
kg/m
7
Bar
28
kg/h
8
mBar
29
gl/s
9
Pa
30
gl/m
10
kPa
31
gl/h
11
Hz
32
ft/s
12
Rpm
33
f3/s(ft3/min)
13
V
34
f3/h (ft3/h)
14
I
35
lb/s
15
kW
36
lb/m
16
HP
37
lb/m
17
mpm
38
lb/h
18
ft
39
ppm
19
m/s
40
pps
20
m3/s(m 3/S)
EPI-18 EPID1 Unit
Scl
Adjusts the scale to fit the unit selected at EPI-17 EPI1 Unit Sel.
EPI-19 EPID1 Unit
0 %
EPI-20 EPID1 Unit
Sets the EPID1 Unit 0% value and the EPID1 Unit 100% value as the
minimum and maximum values set at EPI1-17.
Summary of Contents for H100
