background image

10 

 

Warranty  

Product is covered  by 2 years Limited Warranty (from the date of purchase). Limited Warranty covers 
any defects in material or manufacturing defects under normal use and maintenance. 

We reserve the 

right not to accept the claim in the case of mechanical damage that could be related to the defect of 
the product or if the product was disassembled by unauthorized service.

 

This  limited  warranty  also  does  not  cover  any  problem  that  is  caused  by  conditions,  malfunctions  or 
damage not resulting from defects in material or workmanship. 
 
During  warranty  period,  we  will  repair  or  replace  defective  product  or  defective  parts.  To  obtain 
warranty service, you must first contact us to determine the problem and the most appropriate solution 
for you. 
 

Safety notice 

This  device  should  be  installed  by  specialized  garage  or  service.  Inappropriate  mounting  or  electrical 
connection  may  result  in  damaging  this  or  any  other  electrical  devices  in  the  motorcycle.  Improper 
installation of fuel hoses can cause the fuel to leak and a fire resulting in damage the motorcycle and the 
owner’s health. 
Device is not approved for use at public roads. You use it at your own risk and responsibility.  

 

Troubleshooting 

If you obey all the instructions, this fuel gauge should work properly without problems. In case of any 
problems, feel free to contact us. 
 
-

 

If the gauge doesn’t show anything on the display, check out all the connections of the device.  

-

 

If the gauge shows nonsense and is calibrated correctly, try checking, if you filled up the fuel hoses 
like explained on page three. 

-

 

Wrong data display is often caused by dirty fuel strainer in the fuel tank, dirty fuel filter if the gauge is 
connected after it or just marginally opened fuel cock. In case of problems, try to check/replace these 
parts.  This  fault  is  often  represented  by  the  amount  of  fuel  dependant  on  engine  revs.  Pressure 
sensor fail is very improbable – problems are usually caused by something else.  

 
If nothing helps, contact us. 
 

 

 

 

Summary of Contents for FGP-DIG-SEG













Reviews: