VESA Plate
(4 pcs.) Cover Screws
Wall Plate
5/16" Hex Bolt
3/8" Hex Bolt
(2pcs.) Covers
Steps 1-4
4mm x 25mm Set Screws
5mm x 30mm Set Screws
6mm x 30mm Set Screws
4mm x 12mm Phillips Screws
5mm x 12mm Phillips Screws
6mm x 12mm Phillips Screws
Hardware List
3/8-16 x 4-1/2" Hex Bolt
3/8" Flat Washers
3/8-16 Nylock Jam Nut
5/16-18 x 2-1/4" Hex Bolt
5/16" Flat Washers
5/16-18 Nylock Nuts
5/16-18 x 1-1/2" Socket Button Head Screw
5/16" Belleville Washers
1/4-20 x 1-1/2" Socket Button Head Screw
1/4" Belleville Washers
1/4-20 Nylock Nut
#8-32 x 1/2" Phillips Self Tapping Screws
#14 x 2-1/2" HWH Lag Screws
1. Remove the 5/16" Hex Bolt from the Wall Arm.
2. Remove the Cover Screws and Covers. Remove the 3/8" Hex Bolt from the
Wall Plate. Set asode the Wall Arm, VESA Plate, Covers and Hardware.
3. Use the Wall Plate as a template to mark and drill 1/8" pilot holes for each
of the Lag Screw locations. Check to make sure the Wall Plate is level before
marking and drilling the pilot holes. Drill the top and bottom holes first. Then,
drill the middle pilot hole with the Wall Plate level. (If installing in metal studs
or concrete, hardware kits can be purchased separately.)
1 ...
7 ...
1 ....
1 ...
2 ...
2 ...
1 ...
2 ...
1 ...
4 ...
1 ...
4 ...
3 ...
6 ...
6 ...
6 ...
6 ...
6 ...
6 ...
12 ...
12 ...
12 ...
36 ...
18 ...
4mm Hex Nuts
5mm Hex Nuts
6mm Hex Nuts
5mm Flat Washers
1/4" Flat Washers
Monitor Attaching Hardware
Protected under one or more of these U.S. Patent numbers: 3,291,432 3,559,942 3,724,798 DES.270,689 4,613,109 4,878,645 4,852,842 DES.309,5624,973,023 5,169,114 5,255,884 5,310,152 5,522,576 5,621,614 Re.35,677 DES.398,834 5,826,384 5,941,492 5,964,068 6,060,661 6,102,398 6,158,704 6,454,116B1 6,761,276B2 6,806,425B1
LC200WDA INSTALLATION INSTRUCTIONS Page 1 of 3
LC200WDA - Articulating Wall Mount
for up to 35Lbs Flat Screens
Important! Please read all warnings and cautions before installing the mount.
Caution: Improper installation of this mount may void the warranty on your monitor.
Caution: Installation should be performed by qualified installers only, using construction methods prescribed
by authorized architects or engineers that comply to all applicable codes and standards.
The maximum weight of monitor to be installed on the LC200WDA is 35lbs (15.9 kg)
Inspect all parts to make sure there is no shipping damage. Do not install if any parts are damaged.
Please call 1-800-LUCASEY or 1-510-534-1435 if you have any questions about this installation.
LC200WDA _Instructions (2/11) ©2011 Lucasey Manufacturing Corporation, Oakland, California www.lucasey.com
