If,
YES
, continue with next Step.
If,
NO
, resolve problem, contact next level of technical support as required. Do not continue until problem is
resolved.
8.
At MCC page 1190, are MCTSI-1 external references 0 and 1 in
STBY
state?
If,
YES
, continue with next Step.
If,
NO
, resolve problem, contact next level of technical support as required. Do not continue until problem is
resolved.
11.56.5.2 Verify Timing Reference Connections for MCTSI Side 0
1.
At MCC page 1190 switch MCTSI-1 to active side, enter command
403
.
Response:
MCTSI-1 REF 0 and 1 ACTIVE
MCTSI-0 REF 0 and 1 STBY
2.
Observe a 15 minute soak period.
NOTE:
Should problems occur, contact the next level of technical support and resolve problem. Do not
continue until problem is resolved.
3.
At MCC page 1190, with MCTSI-1 active remove MCTSI-0 from service:
enter input command
200
Response:
RMV MCTSI = a-0 COMPLETED
Where:
a =
EXM-2000 number
4.
At the MCTSI cabinet, side 0 PCD pack, depress:
OFF
button.
Response:
REPT PWR OFF MCTSI = a-0
Where:
a =
EXM-2000 number
5.
Visually verify connection of output clock reference cable as shown below.
FROM
TO
BITS BOX
(See
Figure 11.56-2
)
TSICOM-0
(See
Figure 11.56-3
)
EQL 62-020 (TSIU4), 353 (Berg Connector)
EQL 45-017 (TSIU4-2), 353 (Berg Connector)
6.
Perform BITS Box acceptance tests. Refer to vendor documentation.
235-105-210
October 1999
Copyright © 1999
Page 7
Summary of Contents for 5ESS-2000
