14.1.4.3 Restore MTTYC 1 To Service
1.
At the MCC, to restore MTTYC 1 to service, enter
RST:MTTYC=1;
Response:
The system displays
RST MTTYC 1 COMPLETED
NOTE 1:
DO NOT STOP DIAGNOSTICS ONCE THEY HAVE STARTED
. If diagnostics are
stopped before the MTTYC is diagnosed, update will not occur.
NOTE 2:
Do
not
continue until this request has successfully completed.
2.
At the MCC, to switch the ROP and the MTTY to MTTYC 1,
enter
SW:PORTSW;
Response:
The system displays
SW PORTSW COMPLETED FOR MTTY
followed by
SW PORTSW COMPLETED FOR ROP
3.
At the MCC, to display AM, AM PERIPHERAL Page, enter poke command
111/112
Response:
AM, AM PERIPHERAL Page displayed.
4.
Verify that the
EAI
status box is available on AM, AM PERIPHERAL Page.
5.
Bring up the
EAI
page and verify that pokes
28
and
29
are available.
Response:
Pokes
28
and
29
are visible on the
EAI
page.
6.
Soak the changes for 15 minutes before performing the remaining steps.
14.1.5 Configure MTTYC 0 For ABD Update
1.
At the 111/112 Page, verify that the MTTY and the ROP are connected to MTTYC 1 and CU 0 is active.
2.
At the MCC, to remove MTTYC 0 from service, enter
RMV:MTTYC=0;
Response:
The system displays
RMV MTTYC 0 COMPLETED
14.1.5.1 Prepare Transaction Block For ECD MTTYC 0
1.
At the MTTY, ensure terminal is in CMD mode, type and enter
199
Response:
RCV ECD Parameter Info page is displayed with cursor at
1. database_name:
2.
Type and enter
incore
Response:
Cursor at 2. review_only.
3.
Type and enter
n
Response:
Cursor at 3. journaling.
4.
Type and enter
*
235-105-210
October 1999
Copyright © 1999
Page 6
Summary of Contents for 5ESS-2000
