Procedure 6.6: MOUNT TAPE ON 9-TRACK TAPE DRIVES
OVERVIEW
NOTE:
For specific information on the
5ESS
®
-2000 Switch Compact Digital Exchange (CDX), refer to 235-120-010,
Compact Digital Exchange Reference Guide
and 235-120-020,
Compact Digital Exchange User's Guide
.
PROCEDURE
1.
If the operation that is to be performed is a ``read only'' operation, then remove the ``write enable'' ring from
the back of the tape reel. If the operation that is to be performed will write data to the tape, verify that the
``write enable'' ring is installed on the back of the tape reel.
2.
Remove outer ring from reel.
3.
Open tape drive door.
For
KS-23909, L21 tape drive:
Make sure the drive is OFFLINE. The door cannot be opened unless the drive is OFFLINE. If the drive
is ONLINE, press the
ONLINE
key once so that ONLINE is no longer displayed.
For
KS-23909, L10 tape drive:
Wait for the power-on sequence to end with momentary OK, followed by NO TAPE messages on the
display. Then the door can be opened.
4.
Mount tape on tape drive. Ensure the tape end is free. For new reels remove the adhesive strip and/or rubber
block that constrains the free end.
5.
Thread tape onto drive following local procedures.
NOTE:
The KS-23909, L10 is an auto-load tape drive. Threading of tape onto take-up reel is not required.
Refer to
Lucent Technologies KS-23909, L(40) Information Manual for the KS-23909 1600/6250 CPI
Recorder (with SCSI Interface).
6.
Close door on tape drive.
7.
Press the
LOAD
(or equivalent) button.
Response:
Tape should move then stop.
BOT
(or equivalent) light should be on.
8.
Press the
ONLINE
(or equivalent) button.
Response:
ONLINE
(or equivalent) light should be on.
Comment:
Tape is now ready for use.
Results:
Tape mounted on drive.
9.
STOP. YOU HAVE COMPLETED THIS PROCEDURE.
235-105-210
October 1999
Copyright © 1999
Page 1
Summary of Contents for 5ESS-2000
