Procedure 6.9: MAKE SOFTWARE UPDATE(S) OFFICIAL
PROCEDURE
1.
Determine if breakpoints have been set in the switch.
NOTE:
Breakpoints must be removed before continuing.
Type and enter the following:
Input
Output Response if Breakpoint(s) Exist
For SM:
op:ut,sm=1&&192,util;
OP UT SM UTILFLAG
For AM:
op:util;
OP UTIL COMPLETED
STATE - ENABLED
For CMP:
oput,cmp=1,util;
OP UT CMP UTILFLAG
2.
Do breakpoints exist?
If YES, continue to next Step.
If NO, go to Step 4.
3.
To remove breakpoints, type and enter the appropriate commands:
(Refer to Input Manual (235-600-700) for complete command.)
For SM:
clr:ut:sm=1&&192,util;
For AM:
clr:util;
For CMP:
clr:ut:cmp=1,util;
NOTE:
The appropriate personnel should be notified that the breakpoints have been cleared.
4.
Using listing of software updates,
OP:STATUS,LISTDIR,FN="/etc/bwm";
, pick software update with lowest
sequence number.
5.
On master control center (MCC) Page
1960
, in order to start the software update process, type and enter:
9000,"yyyyyyyyyy"
Where:
yyyyyyyyyy
= 10-digit software update number, craft (CFT) software update number, or
temporary (TMP) software update number. EXAMPLE:
BWM93-0011
.
Response:
ENTER 9010 TO VERIFY BWM
6.
On MCC Page
1960
, enter command
9010
to verify software update and build executable message file.
Response:
UPD VFY COMPLETED
Apply section displayed under ``SECTION EXECUTION STATUS.''
NOTE:
If fails, check to see if "bwm" exists in file, or if "bwm" name was typed in error. Retry BWM second
time, reload from TAPE or SCANS, if error message, seek assistance.
7.
On MCC Page
1960
, enter command
9250
to print entire message file.
Response:
Message file printed at receive-only printer (ROP).
235-105-210
October 1999
Copyright © 1999
Page 1
Summary of Contents for 5ESS-2000
