manualshive.com logo in svg

Lucent Technologies 5ESS-2000, Operations And Maintenance Procedures

The Lucent Technologies 5ESS-2000 is a revolutionary telecommunications system. Our website offers free downloads of user manuals containing comprehensive Operations and Maintenance Procedures. Upgrade your system's performance and troubleshoot issues effortlessly by accessing our detailed manual. Download it for free from 88.208.23.73:8080 to enhance your telecommunications experience.

Share
Download
background image

The NT1 or first BRITE CU that is connected to the U-card does not match the type of service assigned to the
customer at line card provisioning time. An example is if the customer subscribes to AMI U-DSL services, but
an 

ANSI

 NT1 is installed at the customer's premises. This is an NT1 mismatch.

The automatic mismatch test runs an electrical test on the U-card tip and ring, applying voltages and measuring
currents, to determine what might (or might not) be connected to the U-card loop. The goal is to prevent
mismatches, namely, to have 

ANSI

 Standard U-cards connected to 

ANSI

 Standard NT1s or CUs, and to have AMI

U-cards connected to AMI NT1s or CUs. On an hourly basis, the automatic mismatch test runs on all U-cards that
have D-channel port status indicating that ISDN layer 1 is not established at the 2-wire U-interface. Layer 1 may not
be established because of a mismatch condition. When the automatic mismatch test detects a mismatch, then the
D-channel port status supplementary information is updated to MSMTCH to indicate the mismatch condition, and a
summary report is printed to the ROP for all U-DSLs that are found with a mismatch condition.

There are several office parameters that provide control of the automatic mismatch test, and the automatic
mismatch test report. They are mismatch detection enable and report parameters found under RC/V view 8.1.

ENABLE:

 This parameter allows or inhibits the automatic mismatch test from running in the entire office.

REPORT:

 This parameter allows or inhibits the automatic mismatch test report from printing in the entire office.

There are additional controls for automatic mismatch and its report. These controls are on an SM/SM-2000 basis
and can be used to inhibit or allow the automatic mismatch mechanism. This is controlled through the input
messages 

INH:MISMATCH

 and 

ALW:MISMATCH

. However, the SM/SM-2000 controls are subordinate to the

office parameters. This means that if the office parameter is set to no, then the SM/SM-2000 controls have no
affect.

3.6  FILE AND FILE SYSTEM MANAGEMENT

3.6.1  INTRODUCTION

Maintaining the file system includes the following:

Checking file system resources

Manipulating files

Using the file system audits

File system corruption detection [system integrity verification (SIV)]

Backing up and restoring file systems.

3.6.2  GENERAL

This subject lists and briefly describes the input messages and reports used in managing files and the file system.
These messages and responses are used in performing various actions such as reporting the contents of a file or
directory and copying a file from an active disk to an off-line or out-of-service disk.

The input/output messages are categorized according to the function performed on the file or file system and how
they are used (Type). The different functions and the corresponding tables are as follows:

File System Control

Table  3-1

235-105-210

October 1999

Copyright © 1999

Page 14

Summary of Contents for 5ESS-2000














































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 5ESS-2000

N-Tron 900 Installation & User Manual preview
900
Brand: N-Tron Pages: 18
CAME FROG PLUS Manual preview
FROG PLUS
Brand: CAME Pages: 2
Radial Engineering SW8 Owner'S Manual preview
SW8
Brand: Radial Engineering Pages: 12
Kathrein EXE 159 Manual preview
EXE 159
Brand: Kathrein Pages: 41
Accton Technology ES4626 Management Manual preview
ES4626
Brand: Accton Technology Pages: 523
Pilz PSEN 1.2p-25 Operating Instructions Manual preview
PSEN 1.2p-25
Brand: Pilz Pages: 8
Sunix ESW-5162GP User Manual preview
ESW-5162GP
Brand: Sunix Pages: 55
GE USB 2.0 7-Port Hub HO97916 Instruction Manual preview
USB 2.0 7-Port Hub HO97916
Brand: GE Pages: 19
NeoPro DOC42 Integrator Manual preview
DOC42
Brand: NeoPro Pages: 36
H3C S6890-54HF Installation, Quick Start preview
S6890-54HF
Brand: H3C Pages: 3
IBM 4002-C4A Installation And User Manual preview
4002-C4A
Brand: IBM Pages: 94
B&B Electronics ICE-104P How To Use preview
ICE-104P
Brand: B&B Electronics Pages: 2
Booma-RC Hidden Ignition Switch Manual preview
Hidden Ignition Switch
Brand: Booma-RC Pages: 16
SEH IH-304 User Manual preview
IH-304
Brand: SEH Pages: 40
Festo SMT-8-...-B Series Manual preview
SMT-8-...-B Series
Brand: Festo Pages: 2
ALFAtron MUH88E User Manual preview
MUH88E
Brand: ALFAtron Pages: 45
Lindy CONNECTION PERFECTION 32797 User Manual preview
CONNECTION PERFECTION 32797
Brand: Lindy Pages: 10
Channel Vision IR-1203 User Manual preview
IR-1203
Brand: Channel Vision Pages: 2

Brands by name

Popular brands

Load more brands