If
YES
, go to Step 24.
If
NO
, continue with the next step.
23.
At the MCC terminal, type and enter:
RESET:FANALM CU a;
Where:
a = 0 or 1.
Response:
REPT MULTIPLE FAN ALARM CLEARED
message received.
FAN A
and
B
LEDs off.
24.
Have fuses
F2A
and
F1A
been tested?
If
YES
, go to Step 26.
If
NO
, continue with the next step.
25.
Substitute
F2A
for
F4A
and
F1A
for
F3A
and repeat from Step 16.
26.
At selected CU power switch, operate
ROS/RST
switch to
RST
position and wait for selected CU and all
subunit
RST COMPLETED
messages to be received.
27.
NOTE:
All subunits and CU are diagnosed and restored to service.
Verify the following responses.
Response:
RST COMPLETED
message received.
At common processor display page, unit label indicates
ACT
(CU indicates
STBY
.
At selected CU power switch,
OOS
and
RQIP
LEDs off.
28.
At selected processor bay, for selected DFC, remove and immediately replace fuse
F5A
.
29.
Verify that
OFF
LEDs are lighted on respective
495A
or
494GA
power units.
30.
Verify that
REPT POWER DOWN
or
REPT UNAVAILABLE
message is received and major alarm is
indicated at terminal.
31.
At selected processor bay, for selected DFC, operate
TN3
power switch to
ON
.
Response:
REPT POWER UP
or
REPT OUT OF SERVICE
or
REPT FAULT CLEARED
message is
received.
Unit label indicates
OOS
or
OOS MAN
.
OOS
LED is lighted on designated unit power switch.
32.
Unlatch and unseat the selected DFC power unit 495FA - C located in cabinet 047 and frame location 016.
33.
Verify that the following responses are obtained.
Response:
ALM
and
OFF
LEDs lighted on DFC power switch.
Major audible alarm indicated at terminal.
REPT FAULT
or
REPT POWER DOWN
or
REPT UNAVAILABLE
message received.
235-105-210
October 1999
Copyright © 1999
Page 3
Summary of Contents for 5ESS-2000
